Top 6 Best 5v Relay

The module uses genuine quality relay, normally open interfaces , Maximum load AC 250V10A, DC 30V10A.. Using SMD optocoupler isolation, strong driving capability, stable performance trigger current 5mA.. Fault-tolerant design, even if the control line is broken, the relay will not move.. The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient.. The Module can be set by jumper high or low trigger..

The Relay Board Maximum load AC 250V10A, DC 30V10ATrigger current of opto-isolator 5mA.. Using SMD optocoupler isolation, strong driving capability, stable performance.. Can be set high or low level trigger with jumper cap, to meet the demand of more trigger applications.. Fault-tolerant design, even if the control line is broken, the relay will not move.. Wide Application,The relay board works well with ARM PIC AVR MCURaspberryCNC machine PS4 etc..

1 Channel Relay Module- This Relay Board provides a single relay that can be controlled by any 5V digital output from your microcontroller.. Main Specification- Peak Load of NO Connector AC125250V10A, DC2830V10A Trigger Current 5mA 4pcs 3.1 mm Fixed Bolt Hole. Adopted SMD Optocoupler Isolation- The isolation circuit prevent damages to I O port by relay switch current.. Wide Application- These 5v relay board works well with ARM PIC AVR MCURaspberryCNC machine PS4 etc.. Humanization Design On Interfaces- All interfaces can be directly wired out through the terminals..

It is 4 Channel Isolated 5V 10A Relay Module, each relay can individually switch onoff by an opto-isolated digital input, Standard interface can be directly connected with microcontrollers and be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, DSP, etc., very convenient.. Equipped with high-current relay, maximum load AC250V 10A, 15A 125VAC, DC30V 10A Trigger current of opto-isolator 5mA.. RELIABLE Fault-tolerant design, even if the control line breaks, the relay will not move With optical coupling isolation, triggering more reliable, more stable.. EASY to INSTALL Equipped with screwed terminal plate and fixed bolt holesdiameter 3.1 mm on both sides for easy installation.. HighLow level trigger can be selected by jumper. Very versatile, you can reverse the input logic with the jumper..

Microcontroller development board can be used as modules, can be used as appliance control. 5V - 12 V control signal of the TTL. Control DC or AC signals can control the 220V AC Load. There is a normally open and open normally closed contact. Useful to control a motor, a led strip, or any other module. How to use it Just connect a digital output of your board to your relay module, and you can control a power-demanding appliance with the digital signal.

Name kits module. 5V relay module 1 way relay module. New 5V relay module. This product contains 5 modules. 100 brand new.

Module uses genuine high quality relay, normally open interface maximum load AC 250V 10A, DC 30V 10A. Using optocoupler chip isolation, strong drive capability, stable performance trigger current 5mA. Module can be set by jumper high or low trigger. Fault-tolerant design, even if the control line is broken, the relay will not move. The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient.

Solid State Relay Module Board has been assembled, and electrical test passed. Led indicator for each relay. Size 155 x 55 x 24 mm approximately 6.1 x 2.17 x 0.95 inch. Has been assembled, and electrical test passed. Led indicator for each relay. Size 155 x 55 x 24 mm approximately 6.1 x 2.17 x 0.95 inch Input control signal voltage 0V - 0.5V Low stage SSR is OFF, 0.5V - 2.5V unknown state, 2.5V - 20V High state SSR is ON SSR Output each channel. Load voltage range 75 to 264VAC 5060Hz Load current 0.1 to 2 AMP Standard interface that can be controlled directly by microcontroller Compatible with Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic.

Equiped with high-current relay, AC250V 10A DC30V 10A. 5V 4-Channel Relay interface board, and each one needs 50-60mA Driver Current. Be able to control various appliances, and other equipments with large current. ApplicationSupports all MCU control, The industrial field, PLC control, Smart home control. Indication LED's for Relay output status.

Driver Current15-20mA each. Indication LED's for Relay output status. IN can be high or low level control relay. Equiped with high-current relay, AC250V 10A DC30V 10A. Standard interface that can be controlled directly by microcontroller Compatible with , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic.