Top 6 Best Arduino Oled Display

0.96 inch,Resolution 128 x 64, View angle 160, Support voltage 3.3V-5V DC, Power consumption 0.04W during normal operation, full screen lit 0.08W. Embedded Driver IC SSD1306. Communication I2CIIC Interface, only need two I O ports. It compatibles with R3 board and Mega, Raspberry pi, 51 MCU, STIM 32, etc.. No backlight is required, and the display unit can be self-luminous. It has ultra-high contrast, bright and clear dots, and it is easy to read even small fonts. There are no fonts embedded in the OLED controller, users can create fonts through font generation software..

UCTRONICS 0.96 Inch OLED Module for showing graphical textual information directly on your micro-controller projects. It supports many chips Arduino UNO and Mega, Raspberry pi, 51 MCU, STIM 32, etc., the UNO shown in the picture is NOT INCLUDE. Resolution 128 x 64, View angle 160, Support voltage 3.3V-5V DC, Power consumption 0.04W during normal operation, full screen lit 0.08W. Embedded Driver IC SSD1306. Communication I2CIIC Interface, only need two I O ports. Needn't backlight, the display unit can self-luminous. It has Super High Contrast, bright and crisp dots, even tiny fonts quite readable. No embedded fonts inside the OLED controller, user can create the fonts through the font generation software. We offer technical support and software library as well as the guide book in the package. Note the display part is 15mm0.5 tall..

Resolution 128 x 32 0.91 Inch OLED display, no need backlight, self-illumination, Display Color White.. Low power consumptio SSD 1306 oled display I2C oled display, IIC I2C communications simplifies connection.. Compatible with Arduino nano, R3 board, Raspberry Pi 4B3B3B2BZero,ESP8266, ESP32, STM32, etc.. Working power3.3-5v, Operating temperature -40 - 85 .. What will you get there are 5 pieces OLED display module OLED display module for you..

Application These serial modules can be used for raspberry Pi 4B3B3B2BZero, Beagle Bone Black,Arduino UNO and Mega, 51 MCU, STIM 32 and so on. Showing graphical textual information directly on your micro-controller projects. 128 X 64 Pixel Needn't backlight, the display unit can self-luminous. It has Super High Contrast, bright and crisp dots, even tiny fonts quite readable.No embedded fonts inside the OLED controller, user can create the fonts through the font generation software.. Changeble IIC Address The IIC address can be changed,it is convenient to use with different machines. Four square holes are easy to install. Support I2c IIC communication Protocol.

This is a general 1.5inch RGB OLED display module, 128x128 pixels, 16-bit high color 65K colors,clearly displays colorful images, with embedded controller, communicating via SPI interface.. Driver SSD1351. Display color RGB, 65K colors. Supports 4-wire SPI OR 3-wire SPI interface, configured via onboard resistor. Dimension 44.5 x 37 mm,Operating voltage 3.3V 5V,Viewing angle 160,Interface 4-wire SPI, 3-wire SPI.

Package List 1 x Yellow-Blue OLED display,1 x White OLED display,1 x Blue OLED display,10 x Female to Female Dupont Cable,1 x Storage Box. 0.96 Inch OLED Module for showing graphical textual information directly on your micro-controller projects. Work great for Arduino UNO and Mega, Raspberry pi, 51 MCU, STM 32, etc.. Resolution 128 x 64, View angle 160,Support voltage 3.3V-5V DC, Power consumption 0.04W during normal operation, full screen lit 0.08W. Embedded Driver IC SSD1306.Communication I2CIIC Interface, only need two I O ports. Needn't backlight, the display unit can self-luminous. It has Super High Contrast, bright and crisp dots, even tiny fonts quite readable.

Interface Selection to choose SPI or IIC interface through R3, R4, R5. For IIC communication, it is necessary to move the resistor on R4 to R3, and R5 is soldered with 0 ohm resistor.. SPI communication or I2C communication can be switched by configuring three resistors R3 R4 R5.

Information 128 x 64 View angle more than 160 degree Support voltage 3.3V-5V DC Power consumption 0.04W during normal operation, full screen lit 0.08W. Functional usages 0.96 inch OLED module for showing graphical and textual information directly on your micro-controller projects It supports many chips compatible with Arduino Mega, Raspberry pi, 51 MCU, STIM 32, etc. Embedded driver IC Communication I2CIIC Interface, only need 2 IO ports Compatible with MMDVM, Pi-Star, and it is compatible with Raspberry pi. Self-luminous design needn't backlight, the display can self-luminous It has high contrast, bright and crisp dots, even tiny fonts quite readable. About fonts no embedded fonts inside the OLED controller, user can create the fonts through the font generation software.

Driver IC SSH1106.Resolution 12864. Four square holes are easy to install. Ultra-low power consumption full screen lit 0.08w. The IIC address can be changed,it is convenient to use with different machines. Supports many control chip fully compatible with Arduino 51 series,msp430 series , stm322 CSR IC etc.

What will you get there are 5 pieces OLED display module with blue display color, self-illuminated and no need backlight. Power-saving display the I2c oled display performs better than the traditional LCD display and with lower consumption sicne the IIC I2C communications simplifies connections Please note that these I2C OLED display module comes without pin headers. More details use compatible with Arduino, ESP8266, ESP32, STM32, etc. 3.35v Power Operating temperature -40 - 85 Resolution 128 x 32. Good compatibility this i2c oled display module is compatitable with Raspberry Pi 4B3B3B2BZero, compatitable with Arduino, also compatitable for ESP8266, ESP32, STM32, etc.. Product manual as shown in the instructions.