Top 6 Best Atmega328

Arduino IDE compatible microcontroller board, ideal for 3D printers, robots and electronic projects, with 14 digital pins, 8 analog and 6 PWM outputs.. It also features 4 UARTs hardware serial ports, 16 MHz clock speed, USB connection, power plug, ICSP connector, reset button and 32KB flash memory, providing everything you need to support the microcontroller. Specifications comes pre-programmed with a bootloader that allows you to load new code without the need for an external hardware programmer.. Input voltage 7 - 12V, Product measurement 101.5 mm width 53.3 mm. SRAM 2 KB EEPROM 1 KB Clock speed 16 MHz. Easy to use Simply plug it into a computer through a USB cable or power it with an AC to DC adapter or battery to get started. You can modify your Uno without worrying too much about doing something wrong.. This Uno board is a microcontroller board based on the ATmega328P data sheet It has 14 digital inputoutput pins 6 of which can serve as PWM outputs, 6 analog inputs, 16 MHz ceramic resonator CSTCE16M0V53-R0, USB connection, power plug, ICSP connector and reset button. It has everything necessary to support the microcontroller. Supplied by MMOBIEL - We always try our best to exceed your expectations every time. Join the ever-growing list of satisfied customers and discover the difference with MMOBIEL..

Main chip Atmel Atmega328P-AU. Fully compatible to Arduino Boards. Support Serial Download, 5V16M. Support external power supply 3.8-12V DC. 3 Pin headers included.

Power the METRO with 7-9V polarity protected DC or the micro USB connector to any 5V USB source. The 2.1mm DC jack has an onoff switch next to it so you can turn off your setup easily. The METRO will automagically switch between USB and DC.. METRO has 19 GPIO pins, 6 of which are Analog in as well, and 2 of which are reserved for the USB-serial converter. There's also 6 PWMs available on 3 timers 1 x 16-bit, 2 x 8-bit. There's a hardware SPI port, hardware I2C port and hardware UART to USB. Logic level is 5V but by cutting and soldering closed a jumper, you can easily convert it to 3.3V logic. USB to Serial converter, there's a hardware USB to Serial converter that can be used by any computer to listensend data to the METRO, and can also be used to launch and update code via the bootloader. Four indicator LEDs, on the front edge of the PCB, for easy debugging. One green power LED, two RXTX LEDs for the UART, and a red LED connected to pin PB5. Arduino IDE compatible, you can use this with the Arduino IDE both desktop and cloud version by selecting 'Arduino UNO' in the Boards menu..

ATmega32U4 microcontroller The Pro Micro is similar to the Pro Mini except with an ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connectivity on-board and do away with bulky external USB interface.. The acceptable voltage range is 5 to 9 V.. On-Board micro-USB connector for programming 4 x 10-bit ADC pins 12 x Digital IOs. This tiny little board does all of the neat-o tricks that you're familiar with 4 channels of 10-bit ADC, 5 PWM pins, 12 DIOs as well as hardware serial connections Rx and Tx. Running at 16MHz and 5V, this board will remind you a lot of your other favorite pro-compatible boards but this little guy can go just about anywhere. If you're supplying unregulated power to the board, be sure to connect to the RAW pin on not VCC.. This latest revision corrects the silk error from the last version of the board so that pin 14 is correctly labeled. We've also added a PTC fuse and diode protection to the power circuit and corrected the RX and TX LED circuit..

ATmega328 running at 16MHz with external resonator 0.5 tolerance. No USB connection off board. Need FTDI board or similar device to program.. Supports auto-reset. 5V regulator. Max 150mA output.

ATMega 32U4 running at 5V16MHz. Supported under IDE v1.0.1. On-Board micro-USB connector for programming. 4 x 10-bit ADC pins. 12 x Digital IOs.

Microcontroller Nano V3.0 ATmega328P. Operating Voltage logic level 5V. Input Voltage recommended 7V-12V. Digital IO Pins 14 of which 6 provide PWM output. Flash Memory 32 KB ATmega328 of which 2 KB used by bootloader.

Over current protected, Max 150mA output.. 3.3V regulator, ATmega328 running at 8MHz with external resonator 0.5 tolerance.. This is a professional version of the Mini Pro, is a microcontroller circuit board.. It has been programmed for its bootloader, without the user to buy ISP burner for programming, user-friendly.. Low-voltage board easy to interface with popular 3.3V devices and modules such as GPS, accelerometers, sensors, etc..

Main Chip Atmega328P-AU. 14 digital input output port RX, TX, D2 D13, 8 analog input ports A0 A7, 1 pair TTL level serial transceiver port RX TX, 6 PWM ports D3, D5, D6, D9, D10, D11. 16MHz clock frequency. The bootloader is already installe in the board. Size22mm33mm.

DESCRIPTION The Atmega328P-PU is the Gold Standard for Arduino Development. We have the Bootloader for use with Arduino IDE and our Version of the Blink Sketch already installed.. SPECIFICATIONS Atmega328P-PU MCUs in DIP-28 Package with Bootloader for Arduino UNO R3 already installed the Bootloader Setting requires an external 16MHz Crystal and a power supply of 3.8 to 5.5V. DIMENSIONS n.a.. CONTENT 10x Atmega328P-PU Microcontroller with Bootloader for Arduino IDE and a Blink Sketch installed. PLEASE NOTE Visit our Amazon Store for more exciting Electronics. For Downloads, Documentation and Product Support please visit UNIVERSAL-SOLDER Website..