Top 6 Best Desolder Wick

Quicker wicking This Solder wick can be used to remove the unwanted excess solder quickly and efficiently during the solder re-working process or remove some already soldered components. The added Flux gives a faster action and helps the surfaces to be heated and solder to flow, which significantly reduces the solder repair time.. Copper braids The braid desoldering wicks are made of 100 copper wires with fine braids woven together, and have good thermal conductivity. Also using the solder braid will protect the delicate components or electronic circuit boards from damages during solderingreworkingrepairing.. Wick Application The desoldering braid wicks are suitable for industry welding, lab work or home work, practical desoldering tools to clean a joint from excess solder and correct mistakes on small PCB boards, the desoldered components can be used again, bringing lots of convenience for your work.. Easy to use Simply just place the soldering wick against the solder and place heated solder iron tip on it, the soldering wick absorbs the solder due to its high thermal conductivity. By this way, you can remove the solder from the PCB or any metal surface. Leaves slight flux residue that is non-conductive and non-corrosive so it requires no cleaning.. Packages include 2 pcs of no-clean solder wicks, each wick is 5 ft in length and 0.1 inch in width..

The solder wicks can be used to correct mistakes with small boards on PCBs, remove relays and other components from printed circuit boards, re-solder mechanical keyboard switches, unsoldering old wire from devices, desoldering computer parts such as a motherboard,clean alloy on smd components and more. 1 pieces of no-clean solder wicks, each wick is about 10ft long and 0.1 inch in width, enough quantity and length for your daily needs. This desoldering wick has geometrically-precise weave with copper and rosin, work from the tip of the desoldering wick, once the desoldering wick and the solder has been heated, the solder braid can quickly absorbed molten solder and left a clean working area.. The desoldering wicks are made of copper wires with nice quality, precise weaving design can improve the capillary effect and the redundant solder absorbing ability, increasing your efficiency. The braided solder wicks are suitable for labs, home and industry welding work, practical tools to remove solder and correct errors on small PCB boards, bringing lots of convenience for your work.

Removes up to four times more solder than conventional wick, and extracts solder much faster than wicks based on Type-R fluxes. Residue left behind is halide free and non-conductive, so it does not have to be cleaned off the board. 100 copper wick has fine braid design to promote strong capillary action to pull in excess solder. Available with standard or anti-static bobbins.

High efficiency solder sucker - the desoldering pump designed with double ring and vacuum open button, you can remove solder from circuit board effectively by cocking it and pressing the trigger button with one hand. Desoldering braid wick with rosin - 6 pieces copper solder braid in 3 size, width 2.0mm2.5mm3.0mm, length 1.5m, 2 pieces for each size geometrically-precise weave, can be used to clean the spare solder on the pin away to avoid short circuit, to meet your various of soldering needs. High quality material - the desoldering pump body made of premium quality ABS material, with non-slip sponge and nylon nozzle, anti-static, heat resistant and durable. Wide application - correcting mistakes on small PCB boards, removing relays and other components from printed circuit boards, cleaning small components, re-soldering and desoldering. 7-in-1 solder removal tool - 1pcs solder sucker and 6pcs solder wicks in 3 size.

1.High-quality materials The desoldering wick is geometrically precisely braided with high-quality copper wire, which is resistant to oxidation and corrosion, has good thermal conductivity, low residual and no halide, and clean tin absorption.. 2.Geometric braid design The solder wick adopts a precise geometric braid design, which ensures a large surface tension and tin absorption ability, and reduces the risk of thermal damage to the circuit board.. 3.Widely used No-clean desoldering wick is suitable for welding work in laboratories, industries, schools and homes, It is suitable for all kinds of electronics, electrical appliances, precision instruments and meters. It can absorb tin quickly and a large amount of tin, and is dedicated to remove excess solder.. 4.Easy to use The desoldering braid wick is used to absorb excess solder when removing tin, the fine woven design promotes strong capillary action to suck in excess solder. The main board desoldering spot is removed, and it is used with the soldering station.. 5.Ingenuity quality 1 piece of no-clean solder braided wick 0.078 inch wide, 9.84 ft length, which is sufficient to meet your work requirements. If you have any product questions, you can contact us at any time..

Quality materialsThe Braided Desoldering Wicks are made of 100 copper wires with a fine braid design. Using flat stitch weaving, fast heat conduction, to promote strong capillary action to pull in excess solder.. Easy to use the desoldering wicks can provide an easier way to correct mistakes on small PCB boards and will not make damage to the board, clean small components, suitable for re-soldering and desoldering.. Extensive applications the braided solder wicks are suitable for labs, school, home, and industrial welding work And the wicks adopt a fine braid design to promote strong capillary action, bringing more convenience to your daily work.. Low residue design No-Clean solder wick braid will just leave little residues after use and the residues are non-conductive and non-corrosive, no need to waste your time cleaning it.. Warranty If you have any questions, please feel free to contact us at any time. Thank you.

Conforms to MIL-F-14256E RMA flux and J-STD-004. High purity, oxide-free copper. ESD Electrostatic Dissipative safe for 1.5 m 5 ft bobbins. Environmentally and PCB safe residues. NSF, Nonfood Compounds Program Listed P1, NSF Registration 144209.

Ultra-thin desoldering wick. Responds as much as 50 faster than conventional desoldering braids. Lighter mass and pure copper braid construction. Better thermal conductivity, even at low temperatures. Overheating minimized by requiring less heat for shorter time.

What you get come with 6 packs of no-clean solder wicks, each wick is about 2.5 mm 0.1 inch in width and 1.5 m 5 feet long, enough quantity and length for your daily needs. No-clean design the solder braided wicks will just leave little residues after use and the residues are non-conductive and non-corrosive, you do not need to spending time removing them from the boards. Reliable material the desoldering wicks are made of copper wires with nice quality, precise weaving design can improve the capillary effect and the redundant solder absorbing ability, increasing your efficiency. Wide applications the braided solder wicks are suitable for labs, home and industry welding work, practical tools to remove solder and correct errors on small PCB boards, bringing lots of convenience for your work. Easy to use the desoldering wicks can provide a easier way to correct mistakes on small PCB boards and will not make damage to the board, clean small components, suitable for re-soldering and desoldering.

Package Include - You will get 1 pack No-Clean Solder Braided Wicks.The color of the label is random.. Appropriate Size - The size of the solder wick is 2.5mm x 3m 0.1inch x 10 ft.. Premium Material - The Braided Desoldering Wicks are made of 100 copper wires with fine braid design.Using flat stitch weaving, fast heat conduction, strong capillary action to pull in excess solder.. Solder Braided Wicks - The solder wicks with no-clean design to make sure that just little residues left behind and the residues are halide free, non-corrosive and non-conductive, greatly saving working time.. Applicable Occasions - The no-clean desoldering wicks are suitable for industry welding, labs work or home work.Not only improves work efficiency, but also does not damage the PCB board..

Quality materialsThe Braided Desoldering Wicks are made of 100 copper wires with a fine braid design. Using flat stitch weaving, fast heat conduction, to promote strong capillary action to pull in excess solder.. Easy to use the desoldering wicks can provide an easier way to correct mistakes on small PCB boards and will not make damage to the board, clean small components, suitable for re-soldering and desoldering.. Extensive applications the braided solder wicks are suitable for labs, school, home, and industrial welding work And the wicks adopt a fine braid design to promote strong capillary action, bringing more convenience to your daily work.. Low residue design No-Clean solder wick braid will just leave little residues after use and the residues are non-conductive and non-corrosive, no need to waste your time cleaning it.. Warranty If you have any questions, please feel free to contact us at any time. Thank you.