Top 6 Best Ender 3 Pro Hotend Upgrade Kit

All Metal Design, Up to 300 PrintingWith scientific structure and material selection, the Spider 3.0 Pro All Metal Hotend Upgrade Kit can reach 300 to accomplish better effect of printing with high temperature filaments. It is compatible with PLA, ABS, PETG, TPU, PP, PC, PEEK, PEI, Nylon and more filament.. Large Melting Zone, High-Flow PrintingThe overall melting zone length is 27.3mm, increased by 30 compared with spider hotend v1.0 and other common hotends, which offer a smooth printing experience even with 0.8mm nozzle. Meanwhile, the inner wall of nozzle and heat block adopt fluid polishing process, Ra0.25, greatly enhance fluidity of filament and prevent clogs.. Supporting 300mms High-Speed PrintingThe high-temp heat-resistant insulation sheet is added to maintain the temp of the melting zone, supporting 300mms high-speed printing.The titanium alloy screws were used to reduce the thermal conductivity by 30, which can reduce the transfer of heat from the hating zone to the heat dissipation zone and ensure the smooth feeding. Meanwhile, red copper heat sink to improve heat dissipation efficiency.. Easy to Install, Wide CompatibilitySmall and exquisite external size with modular standard interface design, easy to install. Directly compatible with Ender 3Ender 3 ProEnder 3 V2Ender 3 Max, no modification required. You can find the their high-temperature firmware on Creality website. For Ender 5Ender 5 ProEnder5 PlusEnder2 ProCR 10SCR 10CR10 S5CR10 S4CR 10MiniCR 20 Pro, they require slight modification. PLEASE NOTE NOT COMPATIABLE WITH ENDER 3 NEOENDER3 V2 NEOENDER3 MAX NEO.. Product List Warranty PolicyThis kit comes with a Spider hotend, a thermistor, a copper tube, a thermal grease, an adaptor, silicone sock, wrenches and screws. We provide price protection service, within 15 days of your purchase, if you find the price has dropped, you can apply to make up the difference. During use, if you have any question, please contact us and we weill reply you within 24 hours..

Compatibility 100 Creality Original. This assembled hotend kit from Creality is a plug and play replacement for Ender 3 Ender 3 V2 Ender 3 Pro Ender 3S.. Pluggable the heating tube and temperature thermistor that from control box, connect them with terminal housing and pin. Then you could plug the hotend kit, easier to replace hotend kit.. MK8 extruder hot end kit, white wire was temperature thermistor, braided wire was heating tube 24V 40W. Tip of the nozzle, aluminum heating block, throat pipe built-in teflon.. Five 0.4mm brass nozzle are included in this hotend kit. This kit can work with different sizes of MK8 nozzle 0.2mm0.3mm0.4mm0.5mm 0.6mm0.8mm1.0mm.. Silicone Cover is provided to help keep temperatures on the hotend much more stable and this will result in higher print quality and consistency..

100 Creality Official - Creality Ender 3 direct drive upgrade kit, compatible with Ender 3Ender 3 V2Ender 3 Pro 3D Printer. Supporting all 1.75mm diameter filament especially for flexible filament such as TPU, PLA and other flexible filaments.. Easy Assemble - Switch Bowden extrusion to direct extruder at any time and easy to disassembly. It doesn't affect the inherent function of the printer because it's a full extrusion kit. Come with longer connecting cable, tools, accessories and diagram instruction, easy to assemble.. Smooth Feed-in - Lower torque requirements on the stepper motor, reducing the possibility of the nozzle blockage when retracting filament and malfunction when loading new filament.. Strong Sturdy All Metal Hotend - This direct extruder kit is all metal structure, durable and wear resistant and Integrated structure is convenient for wiring and replacing.. Creality 3D Official Store - We are the ONLY Creality 3D Official store. There are more than 20 engineers for after-sales service and provide 247 customer service with 1-year limited and lifetime technical assistance. Please contact us via ask a questiondirectly to get the professional assistance..

It's 100 Creality Original and Creality-Capricorn PTFE Tubing.. Upgrade with Low Friction Creality-Capricorn Original Teflon Tube 40CM.. Hotend replacement parts suitable for ender 3, ender-3x, ender-3 pro, Ender 3 V2 3d printer.. High Lubricity Additives make our XS Series tubing the lowest friction Bowden tubing on the market. Less friction means more responsiveness, less retraction, more accurate prints, less slippage, wear, and tear on the extruder, and less clogging when printing chunky filaments such as some woodfills or ironfills. Lower retraction means time saved every time the extruder retracts. Over the course of a print, a few milliseconds here and a few there add up to a lot of time saved.. Creality-Capricorn tube is far superior to the white PTFE tubing supplied with most 3D printers. Its much smoother to feed filament through. And when printing it reduces the drag on the extruder giving a much smoother travel and print quality..

It's 100 Creality Original Upgrade Assembled Extruder Hotend.. Original Capricorn XS Serious Bowden PTFE tubing with lowest friction on the market. Less friction means more responsiveness, less retraction, more accurate prints, less slippage, wear, and tear on the extruder, and less clogging when printing chunky filaments such as some woodfills or ironfills.. Pluggable the heating tube and temperature thermistor that from control box, connect them with terminal housing and pin. Then you could plug the hotend kit, easier to replace hotend kit.. With more terminal housing and pins as spare parts, in case fail installation and waste.. MK8 Extruder Hot End kit, white wire was temperature thermistor, braided wire was heating tube 24V40W..

Quality AssuranceThe Ender 3 hotend extruder kit and accessories are all original and high quality from 100 quality assurance. Suitable for Creality Ender 3 Ender 3S Ender 3 Pro. Effective heating and cooling system It has heating block and heat sink and dual fan for cooling. The heating block with insulating silicone cover keeps the temperature stable and ensures even printing. The design with two fans makes heat dissipation more even, solidifies the model quickly and ensures precise printing. Easy InstallationThe kit is assembled before delivery, which means it's quite easy to install even if you are a beginner of 3D printing. You can according the video on the product page to install it.. High Quality Silicone CaseThe non-stick silicone cover keeps the hotend temperature extremely stable and what's more, the extruder looks clean and tidy.. After Sales ServiceCreality pays great attention to the buyers user experience. If you have unsolvable problems during installation and use, please feel free to contact us, our after-sales technical team will provide you with detailed solutions within 24 hours..

100 Creality OriginalCreality Sprite Extruder Pro Kit comes with a CR Touch short cable for compatible with BL TouchCR Touch. This Spirit extruder upgrade kit compatible with Ender 3, Ender3v2, Ender 3 pro and Ender 3 Max.. All Metal Design-High Temperature PrintingWith Compact and light weight design, 54x50x64.3mm small size, 288g weight. Creality Spirit direct drive extruder perfectly combine extruder and all metal hotend, enables all the Ender-3 series 3D printers a direct extrusion and high temperature printing conditionssupport PLA, TPU, PETG, ABS, PA, PC etc and other flexible filaments.. Large Torque, Extrusion Force Up to 80NThe use of gear with 3.51 gear ratio which perfectly matches with motor makes extrusion force up to 80N depending on filaments. More precise control of feeding withdrawal.. Dual Gear Feeding, More Stable Printing The Creality Sprite direct drive extruder adapt double-toothed structure which does not damage filaments, allowing more reliable and stable feeding. With adjustable tensioner, allows you to fine-tune the pressure exerted by the drive gears onto the filament to print more exquisite models.. Six Months Warranty We provide six months warranty for any issue, and life-time professional technical supports, if you have any issue while using it, please contact us seller directly through Ask a Question..

300 high temperature printing Efficient heat dissipationUpgraded to metal material, which supports 300 high temperature printing.Structure upgrade, the design of the split spray cooling system effectively reduces heat transmission and improves heat dissipation efficiency... High-quality upgrade of parts and materialsThe throat is made of titanium alloy and copper alloy closely connected, the 0.2mm ultra-thin-wall thick throat brings excellent thermal insulation performance, the heating block and nozzle are made of copper alloy, and the inner wall roughness of the nozzle is Ra0.3, which improves the printing quality.. High strength and durabilityThe heating block is directly fixed with the fixing bracket to protect the throat from force, and the overall nozzle is more stable and prolongs the service life.. Easy to installModular standard interface design, universal standard nozzle, easy installation and maintenance, This 3D printer hotend kit includes Spider High-temperature Hotend1, Copper tube1, M320 screw2, Wrench1, Hexagonal wrench3, Thermal Grease1.. Compatible with many materialsCompatible with PLAABSPETGTPUPPPCNylonPEEKPEI and other common printing consumables.