Top 6 Best Kamoer

Control Method WiFi Remote Control. Support System iOSAndroid. Firmware Updateable.

WiFi Connection. Suitable for all sorts of continuous dosing applications. Ideal for feeding calcium reactors, Kalk reactors, and bio-denitrators. The perfect pump for building an automatic water change system. Near-silent operation.

1.High flow, High lift, Low cost,LED display. 2.Intelligent power off memory. 3.You can set the running interval. 4.DIP intelligent peristaltic pump supports forward and reverse rotation.. 5.The speed is controlled by the knob to control the flow, and the foot switch can also be used to control the start and stop, which is very convenient.

Kamoer ATO one se automatic water replenisher, a good helper for the fish tank at homeIt has the function of adding water overtime alarm to prevent water level overflow caused by sensor failure.. This ATO is equipped with S1 float sensor, also called anti-overflow sensor to prevent excessive water replenishment and water overflow and S2 optical sensor also called water replenishment sensor. Usually note In the case of ATO running normally, S1 is not working, and the float state is sinking. S2 works.Sensors may fail if not properly installed, make sure they are properly installed or unplugged and reinstalled.. In daily use, S2 is a sensor that detects the lowest water level. The function of S1 is to cause the float to rise when the water level exceeds the S2 optical sensor and reaches the S2 float sensor when S2 fails for example, foam is generated in the sea tank, etc. Alarm, stop refilling.. Please install the sensor correctly the main picture has a picture description, otherwise the product will not work. And the distance between the two sensors is not less than 10cm. The height difference between the make-up bucket and the sumpmaster tank should not exceed 1.5 meters, and the liquid level of the make-up bucket should not be higher than the liquid level of the sumpmaster tank.. Some problems mentioned in product reviews such as quality assurance, installation problems, and product failure to work, etc., please watch the demo video and detailed introduction on the details page. We give a detailed explanation on the details page..

VoltsDC 12V, flow rate3360mlmin, Tube size 2mm ID x 4mm OD, Working temperature 040Relative humidity 80Rotor3 rotors.. Pump tube material Pharmed BPT tubetube service life1000HLong time continuous work will be less.It has very good chemical resistance.The tube is opaque operating temperature range -51132.. With Snap-in type design.Convenient for pump tube replacement and cleaning.No valves and seals.Very easy to remove the pump head.. This peristaltic pump is widely used,experiment liquid dispensing, lab chemical liquid transportbiochemical analysis, pharmaceuticals, biotechnology, family watering,water treatment, etc.. This small peristaltic pump is small but powerfulsuitable for viscous, non-viscous liquid transfer,flow direction can be controlled by the positive and negative connection..

KPHM series peristaltic pump, the new design makes the pump tube is well fixed and prevents the pump tube from moving during operation. It is also a low-cost large flow peristaltic pump with stepper motor.. Motor Stepper motor,Voltage 24V,Current 0.3A,Flow rate 400mlminSpeed 400rpmNet weight 304g,Roller 3 rotors,Working Temperature 0-40,Humidity 80,Pump head material Nylon. Pump tube materialPharMed BPT.Very good resistance to general chemicals, as well as excellent resistance to acids, alkalis and oxides.. No pollution,low pulsation.The gearbox drives the pump tube to work, and the pump tube is not easy to slip.The liquid only touches the pump tube, not the pump body.. ApplicationExperimental ResearchExperimental MonitoringInkjet.PrintingAquariumSmart HomeAviation Operation.

24V, silicone tube 3mm ID 5mm ODPlease contact customer service for other pump tube sizes and models. 19-65mlmin, low noise, ambient temperature 0-40, relative humidity 80, weight 185g including power supply 300g, size L72mm, W86.5mm, H80.2mm.. KXP-X is an affordable complete peristaltic pump. One pump can meet the requirements of multiple flow rates.The volume is very small, and the direction of the pump head can be adjusted. You can also choose other pump head accessories in the shop for replacement.. The operation is convenient, and the user can adjust the flow rate of the pump by rotating the button.. The peristaltic pump head has a snap-fit design, no valves and seals, easy to disassemble, easy to replace the hoseeasy to clean and maintain, and easy disassembly. Suitable for printing equipment pumping ink, scientific research institutions doing experiments, aquarium fish tank pumping, animal experiments blood transmission..

Working power supply 110V-220V, power 20W max, weight 2.5kg, flow range 1-352mlmin, using high-precision stepping motor, longer lifelow noise.. Tube size Silicon tube IDOD 4.0mm7.2mmFor other sizes, please contact customer service.. LCD screen displayTwo language modes, support Chinese and English display., touch button operation, simple and convenient peristaltic pump.. This intelligent peristaltic pump machine can be used when it is connected to the power supply, and it is also equipped with a foot switch that can be used to control the start and stop.. This small liquid dosing pump suitable for filling and sub-packaging in the industrial field, laboratoriesscientific research institutions, constant volume for cosmeticsbeverages, and calcium reactor in the aquarium field..

Kamoer ATO one se automatic water replenisher, a good helper for the fish tank at home It has the function of adding water overtime alarm to prevent water level overflow caused by sensor failure.. This ATO is equipped with S1 float sensor, also called anti-overflow sensor to prevent excessive water replenishment and water overflow, S2 optical sensor also called water replenishment sensor and S3 water replenishment bucket level sensor. It detects the water level of the refill bucket. . Usually note In the case of ATO running normally, S1 is not working, and the float state is sinking. S2 works.. In daily use, S2 is a sensor that detects the lowest water level. The function of S1 is to cause the float to rise when the water level exceeds the S2 optical sensor and reaches the S2 float sensor when S2 fails for example, foam is generated in the sea tank, etc. Alarm, stop refilling.. The float sensor detects whether the water replenishment tank is short of water, and once the water is short, it will stop and alarm.. Please install the sensor correctly the main picture has a picture description, otherwise the product will not work. And the distance between the two sensors is not less than 10cm. The height difference between the make-up bucket and the sumpmaster tank should not exceed 1.5 meters, and the liquid level of the make-up bucket should not be higher than the liquid level of the sumpmaster tank..