Top 6 Best Liquid Level Sensor

The CQRobot non-contact liquid level sensor realizes non-contact detection of the liquid level in a closed container. It adopts advanced signal processing technology and high-speed signal processing chip, breaking through the influence of container wall thickness. It is simple to install and easy to use, and can detect the level of various toxic substances, strong acids, strong alkalis and various liquids in high-pressure airtight containers.. The principle is to use the inductive capacitance of water to detect whether there is liquid. When there is no liquid close to the sensor, the sensor has a certain static capacitance to the ground due to the existence of distributed capacitance on the sensor. When the liquid level slowly rises and approaches In the case of an inductor, the parasitic capacitance of the liquid will be coupled to this static capacitance, making the final capacitance value of the inductor larger.. The changed capacitance signal is then input to the control IC for signal conversion, which converts the changed capacitance into a change of a certain electrical signal, and then a certain algorithm is used to detect and judge the degree of this change. When the change exceeds a certain amount It is considered that the liquid level has reached the sensing point when the threshold is reached.. High stability, high sensitivity, strong interference ability, no external electromagnetic interference, special treatment for power frequency interference and common mode interference, strong compatibility, penetration of various non-metallic containers, such as plastic, glass, For ceramics and other containers, the sensing distance can reach more than 12mm liquid, powder, and particulate matter can be detected.. The sensor comes with 2 DIP switches, the right DIP switch controls the output voltage high level of the signal terminal green line when the DIP switch is dialed up, the high level is 5V when the DIP switch is facing When dialing down, the high level is 3.3V. Compatible with Arduino, Raspberry Pi and Other Motherboards..

Liquid level transmitterInput level transmitter and highprecision diffusion of silicon for more accurate monitoring of water level.. 4-20mAFull digital conditioning circuit, 420mA signal output ensure more stable performance.. IP68 waterproofIP68 multilayer waterproof protection ensure safe use and long service time.. Practical design45 degree oblique angle antiimpact, probe detachable antiblocking design.. Water level transmitterThe measured medium is water, do not test liquids that will corrode stainless steel..

Stable Design High quality solid structure, Anti-bending, high accuracy, high stability, anti-blocking hole design, easy to clean. Premium Quality This liquid level sensor adopts of anti-corrosion material, excellent anti-corrosion performance and durable. Safe to Use The shell is made of stainless steel and durable, and with waterproof cable, safe to use. Fitment 4-20mA transmission output, can be used with digital display, PLC, inverter, recorder and other instruments. Excellent Performance With reverse polarity and current limit protection, laser resistance temperature compensation, programmable adjustment..

Approvals CE, UL Haz. Loc. , CSA Haz. Loc. , NSF. Electrical Ratings 240 VAC, 0. 14A 120 VAC, 0. 28A 120 VDC, 0. 07A 24 VDC, 0. 28A. Stem Material 316 Stainless Steel. Float Material 316 Stainless Steel. Float SG 0. 60. Lead Wires 24, 22 AWG, Teflon Insulated. Max PressureTemp 300 PSI392F 200C. Mounting 12 x 12 NPT. Switch Rating 30 Watt, SPST. Note Switches are rated for resistive loads. See our Electrical Considerations for UL guidelines for current Amperes resistive at different voltages, Minimum through hole size for mounting is 0. 69.

Approvals CE, UL, CSA, NSF. Electrical Ratings 240 VAC, 0. 14A 120 VAC, 0. 28A 120 VDC, 0. 07A 24 VDC, 0. 28A. Stem Material Polypropylene. Float Material Polypropylene. Float SG 0. 50. Lead Wires 24, 22 AWG, MTW Insulated. Max PressureTemp 100 PSI221F 105C. Mounting 12 NPT. Switch Rating 30 Watt, SPST. Note Switches are rated for resistive loads. See our Electrical Considerations for UL guidelines for current Amperes resistive at different voltages.

Package Content 6 x Water Level Sensor Color Light blue and yellow. Model No. DP5200Max Contact Rating 10W. Max Switching Current 0.5AMax Breakdown Voltage 220V DCMax Carry Current 1.0AMax Contact Resistance 100m ohm. Temperature Rating -10 85 CelsuisFloat Ball Material P.PFloat Body Material P.P. Cable Length 39cm 15.3Switch Body Size 65 x 22mm 2.6 x0.87 Thread DiaApprox 16mm 0.63.

Approvals CE, UL, CSA, NSF. Electrical Ratings 240 VAC, 0. 14A 120 VAC, 0. 28A 120 VDC, 0. 07A 24 VDC, 0. 28A. Stem Material Polypropylene. Float Material Polypropylene. Float SG 0. 80. Lead Wires 24, 22 AWG, MTW Insulated. Max Pressure 100 PSI221F 105C. Mounting 18 NPT. Switch Rating 30 Watt, SPST. Note Switches are rated for resistive loads. See our Electrical Considerations for UL guidelines for current Amperes resistive at different voltages.

Contact WaterLiquid Level Sensor, This is a photoelectric water liquid level sensor that is operates using optical principles. Open collector output mode, suitable for connecting various circuits and product applications.. The sensor has no mechanical parts, requires no additional adjustment, and has high sensitivity, low power consumption, corrosion resistance, high pressure resistance, high temperature resistance and chemical stability.. This sensor probe is small in size and has a structure that can be placed up, down, laterally, and diagonally in multiple orientations to detect solution spillage, dryness and horizontal level. Can be used as a reminder and alarm function.. The sensor has a DIP switch. The DIP switch controls the output voltage high level of the signal terminal green line. When the DIP switch is dialed to 5V, the high level is 5V. When the DIP switch is dialed At 3V, the high level is 3.3V.. Compatible with Arduino motherboard and Raspberry Pi motherboard. for Automatic Irrigation Systems, Aquariums, Plants, in The Garden, in Agriculture etc..

Approvals CE, UL, CSA, FLORIDA DEP EQ682. Electrical Ratings 240 VAC, 0. 14A 120 VAC, 0. 28A 120 VDC, 0. 07A 24 VDC, 0. 28A. Stem Material PBT. Float Material PBT. Float SG 0. 75. Lead Wires 24, 22 AWG, Teflon Insulated. Max PressureTemp 100 PSI266F 130C. Mounting 12 x 12 NPT. Switch Rating 30 Watt, SPST. Switches are rated for resistive loads. See our Electrical Considerations for UL guidelines for current Amperes resistive at different voltages, PBT is not suitable for use in water above 149F 65C. Wires are rated for 60C where exposed to oil.

Operating voltage DC3-5VOperating current less than 20mA. Sensor Type Analog. Operating temperature10-30. Humidity 10 -90 non-condensing. Product Dimensions 62mm x 20mm x 8mm.