Top 6 Best Load Cell Sensor

Load Cell Easy to use. With 5-10V driving voltage, the force change is directly output as a voltage signal.. HX711 module A 24-bit AD converter chip specially designed for high-precision load cells.. Connection Red to E Black to E- Green to A White to A-.. Two-way optional differential input On-chip low-noise programmable amplifier with selectable gains of 64 and 128.. Instructions One end of the sensor is fixed by a screw hole, and the other end is left in the air. Apply force in the direction indicated by the label. Please be careful not to directly press the white latex part to avoid damage to the sensor..

The 50kg load cell is a group of half-bridge strain gauge, there are 3 ways to use it. 2.Use two sensors to form a full-bridge measurement, measuring range for the sum of the two sensors 50kgx2 100kg. Use one load sensor 50kg with an external resistor to form a full-bridge measurement, the range of a sensor range 50kg. External resistance on the higher requirements.. Use two weight sensor 50kg to form a full-bridge measurement, measuring range for the sum of the two sensors 50kgx2 100kg. Use four weight scale 50kg to form a full-bridge measurement, measuring range for the sum of four sensors 50kgx4 200kg. If you have any problem, please contact seller as follow click DIYmallsyou can find Sold by DIYmalls under Buy Now button, in the new page, click Ask a question..

HX711 module uses 24 high precision AD converter chip hx711 HX711 a specially designed for the high precision electronic scale design with two analog input channel the internal integration of 128 times the programmable gain amplifier.. LOAD CELL - Sturdy aluminum alloy construction with strain gauges pre-attached with strain relieved wires. Accurately measures forces from 0-5kg 0-11 lb.. On-chip active low noise PGA with selectable gain of 32, 64 and 128.. On-chip power supply regulator for load-cell and ADC analog power supply, on-chip oscillator requiring no external component with optional external crystal.. Simple digital control and serial interface pin-driven controls, no programming needed, selectable 10SPS or 80SPS output data rate..

350 Ohm A resistive strain gauge sensor with a 350 ohm nominal resistance which varies when a force is applied. By measuring the change in the sensors resistance, a measurement of the force applied to it can be obtained.. Constantan FoilThe substrate is made of the modified phenolphthalein, and the grid is made of constantan foil.. High PrecisionWith high precision and good static measurement stability, the weighing sensor is suitable for 0.02 level sensor.. Mini SizeThe 7.14.5mm specification makes it easy to dissipate heat, consumes less power per unit area, and is easy to paste and solder.. Temperature CompensationSimultaneous temperature self-compensation and creep compensation..

Tension and compression both can be used. High accuracy with good stability. Hermetically weldedsealed by adhesive inside. Oil-proof, waterproof. material alloy steel.

The 50kg load cell is a group of half-bridge strain gauge, there are 3 ways to use it. 2.Use two sensors to form a full-bridge measurement, measuring range for the sum of the two sensors 50kgx2 100kg. Use one load sensor 50kg with an external resistor to form a full-bridge measurement, the range of a sensor range 50kg. External resistance on the higher requirements.. Use two weight sensor 50kg to form a full-bridge measurement, measuring range for the sum of the two sensors 50kgx2 100kg. Use four weight scale 50kg to form a full-bridge measurement, measuring range for the sum of four sensors 50kgx4 200kg. If you have any problem, please contact seller as follow click DIYmallsyou can find Sold by DIYmalls under Buy Now button, in the new page, click Ask a question..

This module uses 24 high precision AD converter chip hx711, specially designed for the high precision electronic scale. The load sensor is a group of half-bridge strain gauge, there are 3 ways to use it.. Use one load sensor 50kg with an external resistor to form a full-bridge measurement, the range of a sensor range 50kg. External resistance on the higher requirements.. Use two weight sensor 50kg to form a full-bridge measurement, measuring range for the sum of the two sensors 50kgx2 100kg. Use four weight scale 50kg to form a full-bridge measurement, measuring range for the sum of four sensors 50kgx4 200kg.

This HX711 amplifier module use 24 high precision AD converter chip hx711, dual-Channel 24 Bit Precision AD Module. HX711 load cell AD module is a specially designed for the high precision electronic scale designwith two analog input channel to internal integration of 128 times the programmable gain amplifier. The input multiplexer selects either Channel A Or B differential input to the low-noise programmable gain amplifier PGA. Applications This weighing sensor amplifier module can use to be weight scales, kitchen scale, industrial process control and so on.. What you will get 5pcs HX711 load cell amplifier module. If any question, how to email us Please click Stemeduyou can find Sold by Stemedu under Buy Now button, in the new page, click Ask a question to email us.

Capacity 50kg110lb each Structure Half-bridge. Interior 1000 Ohm half-bridge strain gauge. Insulation Resistance 2000 M Ohm Nonlinearity 0.05 F.S. This load sensor, sometimes called a strain gauge, is the same one found in digital bathroom scales.. This item is used widely in hopper scales, platform scales, platform balance, belt scales and other electronic weighing devices..

This load sensor, sometimes called a strain gauge, is the same one found in digital bathroom scales. The sensor is a group of half-bridge strain gauge, there are 3 ways to use it. This module uses 24 high precision AD converter chip hx711, specially designed for the high precision electronic scale. You will receive 4pcs 50kg Half-bridge Load Cell 1pc HX711 AD Weight Module. If you need technical documentation, please click Geekstoryyou can find Sold by Geekstory under Buy Now button, in the new page, click Ask a question to email us.