Top 6 Best Monoblock Amplifier Car Audio

1500W Maximum Power Monoblock Amplifier. Optimized 563-watt RMS and a max output power of 1500 watts, you can give your music a huge boost in power that will have you and your passengers partying while on the road. Compactly built so this amplifier can fit perfectly into any trunk.

Car audio amplifier with 1500 watts RMS power at 1-ohm load 14.4v 850 watts RMS at 2-ohm load 14.4v 450 watts RMS at 4-ohm load 14.4v Frequency response 0 to 320 Hz Bass Knob Included. Small footprint and compact chassis makes this mono amplifier easy to install in any vehicle or car audio application but dont let the size fool you, this 1500 watt amplifier absolutely pounds. Engineered to be the most efficient car monoblock amplifier in its class so that you can get the most out of your vehicles electrical system. MOSFET pulse width modulated power supply and proprietary heat dissipation design will ensure the amplifier for car subwoofers runs cool for even the most demanding playlists. 4-way protection circuitry features high voltage, low voltage, over current, and high-temperature protection sleep easy at night knowing your class d amplifier car audio is protected.

Class D MOSFET Monoblock Power Amplifier. Peak Power at 1 Ohm 1,600 Watts RMS Power at 1 Ohm 1,200 Watts. Frequency Response 20Hz - 250Hz, On-board Bass EQ Switch with 6 or 12dB boost at 45Hz. Featuring 4-Way Protection Circuitry and 4 Gauge Power Ground Input Terminals for Maximum Current Flow. Damping Factor - 150. Stable at 1 ohm Remote Subwoofer Level Control Included. Highly Efficient Heatsink Design allows for Maximum Reliability Performance.

Power - 3000 Watts Max x 1 1-Ohm, 1500 Watts Max x 1 2-Ohms, 750 Watts Max x 1 4-Ohms, 6000 Watts Max x 1 2-Ohms Strapped Bridged. Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until its needed instead of being converted into heat. Reduction in sizeweight, reduced power waste, smaller heat sink, compact circuitry. 1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to. Strapping Capable - You are able to strap two CG3000.1D amplifiers and double the power that is being sent to your subwoofers. You now have the ability to connect more subwoofers to take advantage of the extra power. Variable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it. Variable Subsonic Filter - To prevent your subwoofers from bottoming out, the variable subsonic filter filters out frequencies below the subwoofers specified low frequency limits and allows the driver to reach a maximum safe excursion. Variable Low Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction. Specs - Dimensions 13.7 x 6.5 x 2.5, Weight 7 lbs.. Warranty - Sound Storm Laboratories provides a powerful 6-year Platinum Online Dealer Warranty so long as the purchase is made through Amazon.Com. We strongly encourage professional installation of this product to ensure proper and safe functionality.

1500 w Max power x 1, 1125 w x 1 RMS 2 ohm, 563 w x 1 RMS 4 ohm Monoblock class ab, MOSFET power supply High and low level inputs Variable low Pass Crossover, switchable bass Boost.

RMS Power Rating 4 ohms 500 watts x 1 chan. 2 ohms 800 watts x 1 chan. 1 ohm 1200 watts x 1 chan.. Pulse Width Modulated MOSFET power supply Wired remote bass level control included. Preamp RCA outputs to daisy chain multiple amps 3-way protection circuitry thermal, overload, and speaker short protection. Heavy duty aluminum alloy heat-sink for extreme heat dissipation Nickel-plated RCA level inputs Nickel-plated screw terminals. Variable low-pass filter 40-240 Hz, 24 dBoctave Frequency response 10-240 Hz Dimensions 12-38W x 7-78D x 2-38H.

Power - 1100 Max x 1 2 Ohms, 550 Max x 1 4 Ohms. Class AB Topology - Class A amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class B amplifiers have no current flowing through its outputs with no audio signal. Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage current precisely by removing the output current sensing loss eliminating all secondary feedback circuitry. Low High Level Inputs - A low level RCA input is measured in voltages. A high level - wire input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers. Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction. Switchable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it. Variable Input Gain Control - The gain control is not for adjusting volume. It simply adjusts the amount of signal that is coming from your receiver and going to your amplifier. Specs - Dimensions 9.13 x 10.44 x 2.25, Weight 4.43 lbs., Speaker Impedance 2 to 8 Ohm, THD RMS Output 0.01, SN Ratio 102 dB, Frequency Response 9 Hz to 50 kHz, Fuse Quantity 1 30 Amp ATO Blade. Warranty - BOSS Audio Systems provides a 6 Year Platinum Online Dealer Warranty for purchases through Amazon.Com. We strongly encourage professional installation of this product to ensure proper functionality.

2000 W MAX Power 2 Ohm x 1 Channel. 1000 W MAX Power 4 Ohm x 1 Channel. High and Low Level Inputs. Variable Low Pass Crossover, Variable Bass Boost. Remote Subwoofer Control. Blue Backlit Illumination. Dimensions Depth 12.8 x Width 7 x Height 2.4.

Excellent for voice as well as bass. 2 ohms. 3000 watts. Mono. Bass boost.

Power - 2000 Watts MAX x 1 1-Ohm, 1000 Watts RMS x 1 1-Ohm, 650 Watts RMS x 1 2-Ohms,400 Watts RMS x 1 4-Ohms. Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until its needed instead of being converted into heat. Reduction in sizeweight, reduced power waste, smaller heat sink, compact circuitry. 1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to. To keep both your car and the stereo amp safe, this ZE1000.1 is equipped w thermal, overload and short circuit protection. Has been specially designed from the bottom up to provide safe and high quality sound in a sturdy form factor. Specs - Dimensions 11 x 6.9 x2, Weight 6.6 lbs..