Top 6 Best Nanovna V2 Plus4

2022 ADVANCED NANOVNA ORIGINAL NanoVNA V2 Plus4 S-A-A-2 is a 4GHz TransmissionReflection vector network analyzer, measuring the S11 Reflection coefficient and the S21 Transmission coefficient of a high frequency network Not only testing standing wave impedance of the antenna, but also can debug the duplexer, the insertion loss of the filter, the isolation and testing the attenuation of the cable, shorten the coefficient, the phase, the amplification of the antenna amplifier. ULTRA-WIDE FREQUENCY RANGE Compared to the previous NanoVNAs 10KHz-1.53GHz, AURSINC NanoVNA V2 vector network analyzer provides a 50KHz-4GHz ultra-wide frequency range with an improved precision and accuration, Moreover, the System dynamic range for this VNA is up to 90dB dynamic range 1GHz and up to 80dB dynamic range 3GHz Plus4 VNA has improved shielding that achieves high dynamic range with an aluminum enclosure. UPGRADED PERFORMANCE PC CONTROL The scanning speed of NanoVNA V2 antenna analyzer increases by 4 times 400 pointssec than previous V2 versions Along with support PC software control, like Windowsabove 7, Linux, MacOS, the VNA can be more compatible with PC and antenna measurements, when measuring the frequency. Flip Display,For your using convenience, you can flip the display as the following steps Menu - Display - Flip Display. LARGER CAPACITY RECHARGEABLE BATTERY The upgraded vector network analyzer is contained with a 3200mAh3.7V lithium rechargeable battery with loger operating time and lasting battery life. Also there are battery charge LED indicators at the back of the VNA which are the battery fuel gauge, the one that is closest to the CH1 port connector is the lowest charge level indicating 25. ORIGINAL NanoVNA V2 Plus4 AURSINC NanoVNA V2 Plus4 is the Original edition if you buy the clone one the VNA cannot proceed the software update forM the official site NanoVNA V2 PLUS4 v2.4 comes with a 4-piece calibration set - open, short, load, thru, two male-male SMA cables, a USB2-B to USB2-A cable black or silver, and a stylus to operate the touch screen menu and markers..

Upgraded VersionThe NanoVNA-F V2 upgraded to the latest Firmware 0.4.0, the operation page is compatible with Nanovna-F. It enables measurements of S-parameter, voltage standing wave ratio SWR, phase map, group delay, Smith chart, DELAY, POLAR, LINEAR and more. Frequency RangeThe measurement range of nanovna-f v2 expanded to 50KHz-3GHz. The TXRX method can measure the complete S11 and S21 parameters, S21 dynamic ranges 70dB 1.5GHz, 60dB 3GHz S11 dynamic ranges 50dB 1.5GHz, 40dB 3GHz. Design of Aluminum Cases Rugged and durable aluminum alloy cases, shielding electromagnetic interference to ensure precise measurements. The SMA radio frequency interface enables seamless connectivity with various measurement devices. 4.3'' Screen 5000mAh BatteryThe nanovna has a 4.3-inch IPS TFT LCD screen with a resolution of 800480 and a resistive touch screen, providing a large viewing angle. It is equipped with an 5000mAh lithium battery for longer standby time, up to 7 hours of usage. With the use of a 2A large-current charging IC, the charging time is reduced. As an add-on, it built-in 5V output for charging Android phones or tablets. PC Android Phone ControlUsing PC software NanoVNA Saver, it can connect to the NanoVNA, extracts data for display and save data in Touchstone files. The PC software enables us to export Touchstone snp files for various radio design and simulation software. Supports Android Mobile Phone only. Packing List1x Host 1x SMA Open Calibration Kit 1x SMA Short-circuit Calibration Kit 1x SMA 50 Load Calibration Kit 1x SMA-KK Double-Head Female Hole Adapter 1x SMA-JJ Double-Head Male Pin Adapter 1x SMA-JKW Elbow Outer Screw Inner Hole To Inner Screw Inner Needles Adapter 2x 20cm SMA-JJ RG405 RF Cable 1x USB Type-C Data Cable 1x Stylus. Software UpdatesUpgrade the website sysjoint.comencontent144.html..

All-Digital IF Technology. Frequency Range from 9 kHz up to 2.1 GHz. -161 dBmHz Displayed Average Noise Level Typ.. -98 dBcHz 10 kHz Offset Phase Noise 1 GHz, Typ.. 1 Hz Minimum Resolution Bandwidth RBW.

2022 UPGRADED HW V3.6 NEW HW VERSION V3.6 with MicroSD card port now can have the measurement data or the screenshots saved in the it at anytime. Added battery circuit management, more secure. Redesigned PCB, you can connect to mobile phone with Type C-Type C cable original PCB needs OTG cable, see a clear HD image on your phone. Added a case, which is protective and dust-proof. Disply 2.8 inch TFT 320 x240. IMPROVED FREQUENCY ALGORITHM The improved frequency algorithm can use the odd harmonic extension of si5351 to support the measurement frequency up to 1.5GHz. The 50K-300MHz frequency range of the si5351 direct output provides better than 70dB dynamic, The extended 300M-900MHz band provides better than 60dB of dynamics, and the 900M-1.5GHz band is better than 40dB of dynamics. MULTIPLE FUNCTIONS The default firmware main function is used for antenna performance measurement. The TXRX method can measure the complete S11 and S21 parameters. If you need to obtain S12 and S22, you need to manually replace the transceiver port wiring. Designed a practical and simple control application on PC, you can download touchstoneSNP files for radio design and simulation software. STRONG AND SECURE POWER SUPPLY This VNA is battery powered or USB powered Built in 650mAh battery, could work for 2 hours continuously, if need extra working time, it can be connected to power bank or power source.. NOTE Our nanovna is only compatible with low-speed and supports SPI mode SD card for now Package include NanoVNA host with battery display 2.8 inch TFT x1, USB Type-C data cable x1, 30mm SMA male to male RG174 RF cable x2, SMA simple calibration kit x1, SMA female to female connector x1.

NEW UPGRADE FNCTION Own our Seesii 3GHz Vector Network Analyzer,you can test the standing wave impedance of the antenna, you can also debug the duplexer, the insertion loss of the filter, the isolation, the standing wave, you can also test the attenuation of the cable, shorten the coefficient, the phase, you can also test the amplification of the antenna amplifier. POWERFUL FREQUENCY METER The improved frequency measurement can measure the antenna frequency of 2.4G up to to 3G. 70dB50KHz-1.5GHz, 60dB1.5GHz-3GHz. Reflection Measure S11 50dB50KHz-1.5GHz, 40dB1.5GHz-3GHz Antenna Analyzer 1.00550KHz - 1.5GHz, 1.021.5GHz-3GHz. IMPROVED ACCURACY NanoVNA SAA-V2 Vector Antenna analyzer equipped with the upgraded shell,Strong anti-interference, improve accuracy.with 3.2 inch touch screen and touchscreen pen,make more accurate and easy to operate.. POWERFUL SECURE POWER SUPPLY This SAA-V2 is battery powered or USB powered Built in 2000mA-h battery, could work for about 3 hours continuously, if need extra working time, it can be connected to power bank or power source.. COMPATIBLE The 3GHz second-generation NanoVNA vector network analyzer is based on OwOComm's S-A-A-2 design, and its performance is greatly upgraded.Can be control by PC,computer software compatible with Linux, Windows 7.

Frequency Range from 9 kHz up to 1.5 GHz. 10 Hz Minimum Resolution Bandwidth. Min. -161 dBm Displayed Average Noise Level Typ.. Min. -98 dBcHz 10 kHz Offset Phase Noise. Level Measurement Uncertainty 0.8 dB. Advanced Measurement Functions Opt.. EMI Filter Quasi-Peak Detector Kit Opt.. VSWR Measurement Kit Opt.. PC Software Opt.. 8 Inch WVGA 800x480 Display.

4.3 inch Large Touch screen and powerful functionHandheld Vector Network Analyzer using 4.3-inch IPS TFT LCD screen, with a larger view angle and can be seen clearly in strong outdoor light.which can measure S-parameter, voltage standing wave ratio SWR, phase map, group delay, Smith chart and so on.. Higher Capacity Battery,and Longer Standby time Upgraded the large capacity 5000mA-h 3.7V battery, longer standby time, and extended USB interface. Typically, it can be used as a mobile power source to charge Android or Apple phones when not in use. The IC is charged by high current 2A, and the charging time is shorter.. Upgraded Aluminium Housing Standard aluminium shell to protect SMA head and reduce the interference of external electromagnetic wave to instrument.. Measurement Range The NanoVNA-F measurement range is 50k-3GHz. You can go to the official website to update and expand the frequency to 10Khz-1.5Ghz.The harmonic expansion of the output signal of the clock chip SI5351 is used to measure the frequency to 1000MHz. At 600M-1GHz, the dynamic range of S11 is 40dB the standing wave ratio is less than 1.02.. Compact and Powerful Upgrade the user program by virtual U disk.Switch to a power switch with a greater sense of operation and a better sense of operation.Support Chinese and English menu switching..