Top 6 Best Network Jack Tester

Automatically runs all tests and checks for continuity, open, shorted and crossed wire pairs. Visible LED status display.. Cable state testing 2-wire Line DC detecting, anode and cathode determination,Ringing signal detecting open, short and cross circuit testing. Cable Type RJ11 Telephone cable and RJ45 LAN cable. Connectors Ethernet Cat 5, Ethernet Cat 5e, Ethernet Cat 6, Ethernet Cat 7, RJ11 6P and RJ45 8P. Power Source DC9V Battery Required not included.

Check wall to switch connections easily without a cable. Easily check for broken or shorted wires. Must have for all pc and network technicians. A very user friendly and simple device. Compact design allows for testing in the tightest of corners.

Troubleshoot cause of problems with patch cords or network to identify open, short, or crossed connections. Verifies proper cabling configuration and good connections. LED clearly lights for each pin as the unit goes through the test cycle. Cable test begins automatically once the cable is plugged in and the power button is on. Test each individual pin - maps the cable.

Cable tester with single button testing of RJ11, RJ12 and RJ45 terminated voice and data cables. Tests CAT3, CAT5e and CAT66A cables. Fast LED responses indicate cable status Pass, Miswire, Open-Fault, Short-Fault, and Shield. Test remote stores securely in tester body. Compact tester easily fits in your pocket.

Identify good connections, opens, shorts and crosses. Automatically scans when cables connected and unit turned on. Two scan speeds fast or slow. Maps connector and cable pin out. Tests cables up to 1,650 or 500 m.

Network cable scanning Three scan modes selectable Digital model Analog mode PoE mode.. Cable continuity testing Test physical status for STP, UTP lan cable.. Cable length measurement Measure cable length and locate fault distance accurately for lan cable.The cable type is CAT5e,CAT6,CAT6aSTPUTP. The test range must be 2.5m200m.. PoE Testing Port Flash Test the information of PoE device, such as PoE voltage, power supply polarity, power supply mode. It can also identify which the type of PSE ataf standard If it is standard PoE device. If it is no-standard PoE device, it only display non-standard. Locate network port by the flashing port light on Hub Switch. Available to 10M100M1000M Hub switch.. Non-contact voltage detecting Detect AC voltage presence 50V-1000V. You can press the PowerSet button on the receiver, if the NCVindicator is light on, then you can use the receiver to detect AC voltage presence..

1.Measures Cable length and display the distance to fault.. 2.Core troubleshooting features length, distance to fault, graphical wire mapping, opens, Shorts. 3. Poe presence identify which pins are providing power and detect how much voltage.. 4. Ping function to test Network performance, data packet, min max Time.. 5. Tone trace Cable with complete AC interference Rejection, much easier than other tracers on markets. 6. Hub blink for locating Network port by the flashing port light on a serverswitchHubRouter ports. 7. Tf card included to export data to computer 50 sets, txt format or online updating.. 8. Voltage detector included in receiver 90-1000V. 9.Any questions , pls contact NOYAFA Store first..

CONTINUITY TEST WIRING DIAGRAM TEST FUNCTION This network cable tester can do the continuity test, which can help you check whether your cable is working normally. The cat6 cable tester is able to determine the distance of open circuit and short circuit. Permits you to locate the wiring error in 5E7E twisted cord network, coaxial cable and telephone line.. LONG BATTERY LIFE 8 FAR-ENDS The network cable tester is a portable unit with long battery life wait-case or standby mode for over 50 hours. The device is equipped with 8 far-ends, and each one has a number to help you clearly locate each line and save your time.. MEASURE CABLE LENGTH ABNORMAL PAIR AND LENGTH FOR RJ45 When you use the network cable tester rj45 to measure the cable length, the normal pair length will be shown in the screen. If there is an open circuit, it will show the specific length range in which this situation occurs. Note that the far end cannot be connected when using pair and length measurement.. CALIBRATION FUNCTION EASY TO CARRY The cat6 cable tester can do self-checking function and automatically compensates any change in battery capacity or ambient temperature. Dynamically calibrates cable length and make length measurement as accurate as 97.Simple and easy to use, big LCD screen to display test results. Compact, lightweight, easy to carry and use.. EASY TO USE HIGH QUALITY Efficient, effective, reliable. A person is enough to complete network cable continuity check and cable sequence. Cat6 cable tester will indicate pair integrity of the cable. Internet wiring tester can auto time delay shut off..

WIRE TRACING MULTIFUNCTION - Fast to locate the breakpoint without wire's cover damage, Find wire on all types of connected operating Ethernet switch RouterPC terminal. Perfect for tracking RJ11, RJ45, cables or other metal wire via adapterAnd also with the Battery10V-110V positive and negative measurements function.. WIRE TRACKER - The Line Finder can trace not only Ethernet LAN wires, but also electrical and speaker wires when connecting to the alligator clip In this situation, the wires must be in power-off status, otherwise the units will be damaged It is recommended to stripe down some of the wires when connecting through the clip Select SCAN Emitter works properly if the SCAN indicator is on Use the receiver to find target wires.. NETWORK TELEPHONE LINE TEST - The Line Finder testes physical connection status of network cable, such as open circuit, short connection, miswire and reverse connection Use the emitter to test the status of working of telephone lines such as judging TIP or RING line, test the line level, positive and negative polarity detection Adjust the volume of receiver by pressing the volume rotary knob.. EARPHONES DESIGN - With a pair of Earphone, you can just connect the earphone to the headset jack of receive to get clear information in a noise environment, Adjust the volume knob to make the volume proper and avoid being interfered. Notice that if the sound is low, you should check whether the battery is powered off or not, and the LED flashlight allows operation in dark situation.. 24-Month Warranty and You Will Get 1x Emitter with double RJ11 RJ45 interface, 1x Receiver with BNC interface,1x Pair of Earphone ,1x RJ11 Clip Adapter Cable,1x RJ45 Cable,1x Storage Box,1x English User Manual , Battery Not Included..

Directly hunt 5E, 6E, telephone wire, coaxial cable, usb cable and other cables. Hub blink for locating network port by the flashing port light on hub switch. Check wiring error in 5E, 6E, coaxial cable, such as open, short, cross, ect. Measure cable length and determine the distance of broken point. Testing polarity and voltage. 8 remote identifiers help to test 8 cables at one time.. Memory for calibration data storage..