Top 6 Best Optocouplers

Gikfun Packing 20pcs OPTOCOUPLER DIP-4 PC817C PC817. Number of Pin 4. Pin Pitch 2.54mm. Optocoupler Output Type optical transistor. Wed like to receive your valuable suggestions for our products and make your idea come true..

Pack of 100 Pieces pc817c Optoisolator Transistor Output 5000Vrms 1 Channel 4-DIP.

Four LEDsThis IC has four LEDs and four photodiodes built-in.. AdvantagesThis allows the low-voltage side to control a high voltage side. OutletOutlet OUT1 OUT2 OUT3 OUT4 output current is equal to the largest HVCC 5.1K, Maximum absorption current 500mA. InputInput IN1 IN2 IN3 IN4, SCM or for Arduino IO port, GND with single-chip microcomputer or for Arduino board GND connection.. PCB Size2524mm0.980.94.

Mounting Through Hole. type6N138,DIP-8. Output Device Darlington With Base. Maximum Power Dissipation 100 mW. Minimum Isolation Voltage 2500Vrms.

This module is used when it comes to the need for isolation control and voltage conversion. br. Drive terminal signal voltage 3.6-24V. Output terminal voltage range 3.6-30V output current depends on the specific situation but the maximum does not exceed 10MA, the total power is constant, the voltage and current are inversely proportionalbr. It can realize 3.3V or 5V to control the interface of 3.6-30V voltage . After the control terminal is turned on, the controlled terminal will also be turned on.br. Photoelectric isolation has strong anti-interference ability. It can drive high-power triodes, MOS tubes and other applications that require high-voltage driving, and can also directly drive low-power 24V relays.If it is a pulse signal, please note that the limit of 817 is 4KHZ or less. If the control signal is greater than 4KHZ, please do not use this module, it will not work properly.br. NOYITO PC817 4-Channel Optocoupler Isolation Board User Manual Download Link including schematic httpswww.amazon.comclouddriveshareE3rlYMWee1xOvEvMUZ97bbRyQyGLYmWttshtUOb6qz0br.

Package 5pcs 1CH photocoupler isolator. DC 12V 1mA. DC 12V high-level trigger with positive phase amplification. The output is equal to the input.. Can be used to input a signal to MCU in isolation or MCU control another device in isolation. They are also good as the level converterNPN-PNP, PNP-NPN.. Optocoupler isolator can be used with other electronic devices to provide isolation between low and high voltage circuits.. Youll typically find these devices being used for Microprocessor inputoutput switching DC and AC power control Communications equipment protection Power supply regulation..

Control DevicesThe 1-channel relay module uses genuine high quality DC5V relay and SMD opto-isolator supporting highlow level trigger, widely apply to control various ACDC appliances, and other devices with large current.. Load RangeNONormally open maximum load AC 250V10A, DC 30V10A. Trigger current of opto-isolator 5mA.. Fault-tolerant DesignThe relay will not operate even if the control line is disconnected.. Universal InterfaceEquipped with screwed terminal plate and fixed bolt holesdiameter 3.1 mm on both sides for easy installation.. High CompatibilityThe relay module can be controlled directly by 5V logic signals from microcontroller8051, AVR, PIC, DSP, ARM, Raspberry Pi, MSP430, TTL logic etc.

Forward current ICEO 50mA Peak forward current ICE Max 1A Reverse voltage 6V Power dissipation 70 mw The maximum collector emitter voltage 35V The maximum collector emitter voltage 6V. Isolation voltage 5000V RMS Current transfer ratio 50 minimum Collector current 50mA. Collector power dissipation 150mW Total power dissipation 200mW Operating temperature -30 100 Degrees Celsius. Collector emitter saturation voltage 0.1V typical value Cut-off frequency 80kHz Number of Pin 4. Package includes 10pcs DIP-4 PC817C PC817 Optocoupler.

This Relay Board Maximum load AC 250V10A, DC 30V10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground.. Main Specification Peak Load of NO Connector AC 250V10A, DC 30V10A Trigger Current 5mA The Module Operating Voltage12V.. These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay NC,C,NO and for input Coil , coil - and trigger.. Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient.. Wide Application These 12V relay board works well with for ARM PIC AVR MCURaspberryCNC machine PS4 etc..