Top 6 Best Plasma Cutting Equipment

Pilot Arc Function This plasma cutter has the pilot arc function. It is a high frequency non-touch arc starting mode. The torch head does not need to touch the metal plate. It can greatly extend the working life of consumables, and increase the cutting thickness plasma cutter with this function can cut steel plates with rust and paint on the surface.. Automatic Cutting 2T is semi-automatic cutting control, 4T is automatic cutting control. Switch to 2T, press and hold the torch switch to start arc and cutting, release the switch to stop arc and cutting. Switch to 4T, press the torch switch to start the arc and cutting.When you release the switch, the torch is still cutting.Press the switch again to stop the arc.. Air Pressure Air Compressor The regulator and gauge are installed in front of the panelyou can read the air pressure value through the air gauge. We recommend air pressure value be in the range of 40-70 PSI. You can also adjust the air pressure through the regulator. The air filter has been installed on the rear of machine with a quick air connector, and the user can use it after connecting with the air compressor. Recommended air compressor 45Lmin.. Cutting Thickness The machine is equipped with a current display. You can choose the current to match the air pressure through the cutting chart which mention in manual, expediently and efficiently. Current display at 110V is 10-35A, Under 220V current display is 10-50A, the maximum cutting thickness is recommended to be 12mm 35A 110V, 60PSI 16mm50A 220V 70 PSI.. Post Time Function BTC500DP with post time function, the adjustment range is 2-15 seconds. This function can be adjusted by yourself extend or shorten the cooling time of the torch head, effectively provide cooling, and extend the working life of consumables. Users can adjust the cooling time required to fully cool the torch head. In generally, we recommend a cooling time of 4-8 seconds, if the Plasma cutter worked too long please cool it for 10-12 seconds..

Plasma Cutter, 110V 35A cutting machine with IGBT inverter technology, It is long life and efficient higher than mosfet machine.. Very good to cut car flame, Clean cutting thickness 6mm Max cutting thickness 10mm,Machine only work in 110V not 220V, Please confirm the voltage before buying this machine. Machine maybe explode if connect it to 220V, Be careful. This plasma cutter with current display and air gauge fixed on panel, Easy read air pressure and current, these functions are great to help the user cut any metal.. The plasma cutter easy to cut stainless steel, alloy steel, mild steel, Copper,aluminum etc. witgh Quality cutting torch PT31 plasma torch, Max cutting thickness is 10mm at 35Amps 110V 50PSI. Machine come with 110V power plug.1 x 4 meters Cutting torch, 1 x2 meters Earth clamp, 1 x 2 meters Air Hose, 1 x Air filter,2 x Tip Nozzle, 2 x Electrode, 2hose clamp,1 x Manual.

EASY TO CUT, POWERFUL PERFORMANCEAutomatic dual-voltage 110220V. With advanced IGBT inverter technology, the maximum severance cut can reach up to 34 20 mm, 12 10mm ideal clean cut, 60 duty cycle. Suitable for alloy steel, stainless steel, mild steel, copper, aluminum, etc. The recommended current is 50A, the recommended psi is between 20-40psi when connecting 110V, the recommended psi is between 30-60psi when connecting 220V.. EASY TO ASSEMBLEWith a plug-in air filter connector and built-in regulator, help you to get rid of tedious installation anymore. Only takes 30 seconds and you can start cutting.. PORTABLE LIGHTWEIGHTThis plasma cutter machine only weighs 13 pounds, easy to carry. It's also tiny and light enough to move with strap in any workplacestrap included.. ADVANCED DIGITAL TECHNOLOGYYou can adjust the post-flow time from 5-15 seconds to have a clean cut. Also could select 2T4T to have a comfortable working experience. The exclusive Large LED design provides you with an accurate data display and helps you read all data easier and more clearly without taking off your helmet.. SAFETY DURABLE ARCCAPTAIN welder machine have passed a variety of professional tests and certifications including TV and ANSI standards before leaving our factory. We provide 30-Day Money Back Guarantee and 2-Years Warranty for you..

Non -Touch Cut-50 Plasma CutterThis plasma cutter can effectively cut rough, painted, rusted metal with less dross. Cutting without touching the metal results in better cutting quality and longer product life. Arc ignition technology allows you to cut without touching the tip to the metal, for better cut quality and longer consumable life.. Output PerformanceVoltage 110220V, 60HZ, 4.8KVA Main fuse 1622A Current rage 20-50A No-load voltage 230V Duty cycle 60 Efficiency 85 Insulation class F Protection class IP21S Max cutting thickness12 Cuts like a hot knife through butter.. Safety DesignBuilt-in over-heat protection, over-voltage protection, under voltage protection. Comes with a mask to prevent you from getting hurt while using it. Compact plasma cutting machine, equipped with portable handle, it is very convenient to operate and carry.. Widely UsedSuitable for sheet metal fabrication, light industrial use, site work, automotive, ducting work, repair and maintenance services. The cutting machine not only use in businesses and DIY users but also fully accommodating the demands of professional operators.. Package IncludedComes with a complete set of tools 1 x cut50 plasma cutters machine, 1pc x earth clamp, 1 x 4m cutting, 1 x air regulator, 2 x plasma tip, 1 x PG head, 2 x gas pipe clasper, 2 x hoop, 1 x pressure reducing valve, 1 x instruction manual, 1x brush, 1x face mask..

NON-TOUCH PILOT ARC Efficiently cuts though rough, painted, and rusty surfaces and produces minimal slag. Pilot arc technology allows you to cut without touching the tip to the metal. Better cutting quality and longer consumable life.. BUILT-IN POST FLOW When you stop cutting, the air runs on for a minute to cool the consumable of the plasma cutter torch. This will extend consumable life.. POWERFUL CUTTING ABILITY 10-55 A DC output, 12ideal clean cut and 34maximum severance cut under 220240V60 Duty Cycle. Uses non-hazardous compressed air to cut stainless steel, alloy steel, mild steel, copper, and aluminum.. LIGHTWEIGHT AND PORTABLE Allows for connection to 110 or 220 volt receptacles without tools, Portable in the shop or at the job siteat 13 l b, the shoulder strap allows the end user to easily move from location to location.. ADDED SAFETY Certificated by ETL, Automatic compensation for voltage fluctuation, over current protection, over load protection, temperature control. NoteDue to the inner structure, the pressure gauge may only read about 30psi, which is the normal phenomenom and it do not affect the whole operation..

AIR PLASMA CUTTER SUITABLE CUTTING for Stainless Steel, Alloy Steel, Mild Steel, Copper, Aluminum, etc. SAFE AND AT LOW COST compact plasma cutter has a handle for portability and uses non-hazardous compressed air to cut stainless steel, alloy steel, mild steel, copper, and aluminum.. OUTPUT PERFORMANCE 10-50 Amp DC output, 12 ideal clean cut and 34 maximum severance cut under 220240V. 10-35A DC output, 13 ideal clean cut and 25 maximum severance cut under 110120V. Engine Power Electric AC DUAL VOLTAGE INPUT Automatic Dual Voltage Dual Frequency 110120 V 220240 V 5060Hz.. BUY WITH CONFIDENCE We offer 30 days refund and a 3-YEARS Limited Warranty include 1 Year NEW Replacement Warranty. US BASED CUSTOMER CARE SUPPORT TEAM please feel free to contact us by phone or email, we always stand Back on Our Products. Please submit the registration form on our website.. THE COMPATIBLE CONSUMABLES SETS for this BROWN Color LT5000D Plasma Cutter are LCS22 or LCS33. Please search Lotos LCS22 or Lotos LCS33 It CANNOT compatible with Lotos LCOn20, LCON40 or LCON90 Consumables Sets or any other third part consumables set. PACKAGE INCLUDES Power supply, Plasma cutting torch, ground clamp, Pre-installed NPT 14 industry type D plug and Air filter regulator, consumables, Instruction Manual, etc.. SETUP WITHIN 1 MIN The pre-installed NPT 14 industry type D plug and air filter regulator allows you to quick connect to your air compressor by using the stand coupler existing on your air compressor. The whole machine can be setup quickly within 1 min..

CUT60 PILOT ARC 3 year warranty 7 day per week support in USA. PT60 blowback cutting torch WITH EURO CENTRAL CONNECTION. Blow-back start technology, Pilot Arc. 60 duty cycle at 60amps, 110220 with adapter. Continuous Pilot Arc enables you to cut expanded, rusted, painted metals.

Air Plasma Cutter GZ GUOZHI 45 Amp Cutter able to cut stainless steel, alloy steel, mild steel,copperaluminum and other metal materials. This cutter can work normally at minus 20 degree. Advanced technology and durable quality.. Advanced Technology Maximum Cutting Thickness is 12 , ideal clean cutting thickness is 25 . High cutting speed, smooth cutting section and no polish demands.. Safety Guarantee GZ GUOZHI 45 Amp Cutting machine with automatic drainage function ,protect the electrode and nozzle.2T4TTEST function,easy to operation. This Cutter with over-heating and over-current protection functions, with excellent and reliable quality, use more safety.. Set Up Within 1 Minute MNPT 14 inch industrial D-type couple, can easily and quickly connect to the air compressor,making it more convenient and easier for the users to use,the users do not need to install the air pressure regulator. The whole machine can be setup quickly within 1 min.. Dual-Voltage High-Quality Accessories 20A-45A current adjustment,90V-260V wide-voltage design,unafraid of the voltage fluctuation, 110V220V dual-voltage automatic conversion. IncludedPT-31 13-feet Plasma torch Gun Assembly,10-feet 500A work clamp assembly, etc.The use of high-quality accessories,durable and not easy to damage..