Top 6 Best Poe Splitter

Support international standard IEEE802.3 af IEEE802.3at30W POE port Support 101001000Mbps data transmission. Transfer Rate 101001000Mbps, Standard IEEE 802.3 I, IEEE 802.3 u, IEEE 802.3 x, IEEE 802.3 afat.. PD support 44V-57V voltage transmission, Automatically detects power supply from PSE power supply module. Support the isolation circuit protection, can effectively protect electrical equipment Support the short circuit, overvoltage protection. 12V 2A power output, easy to access Poe network for non-PoE terminal. 1500V high voltage isolation..

Allows you to run 1 cable run to the switch for 2 cameras that are near each other. Set consists of a sender unit and a receiver unit. Plug Sender unit into 2 open ports on your POE switch. Run one cable to the location that has the cameras that are nearby each other. Connect 2 short cables to the Receiver unit and connect the other ends to your camera. Done. Reduces cabling costs. Lets say you are installing 2 cameras on each side of a corner. Instead of running 2 cables back to the switch, you can now just run 1. Easy and Cost Effective.. Ever installed a camera in a location, only to find out that you need another one right by it Whats worse, the switch is on the other side of the building and it took you hours to run that one cable run. No worries Just use this splitter set to make your installation much easier as all you need to do now is run 1 cable from the old camera to the new camera.. The Receiver Unit comes with weatherproof RJ45 connectors, allowing you to fully expose the Receiver unit to the weather elements.. Simple plug n play installation. Works with all standard 802.3afat POE switches. Also works on POE NVRs due to the new updated design with the onboard toggle switch. If your switch or NVR uses standard POE power, this unit will work.

The PoE Extender features one 30W PoE input port and two 15W PoE output port, running one cable to connect to 2 POE IP devices.. It can forward both Ethernet and PoE power for 1 terminal equipment via Cat5,Cat5e,Cat6,Cat6e,UTP cableless than 120m.. Supports 10,100Mbps data rates, comply with IEEE802.3at and IEEE802.3af Standard. Provides 802.3af power levels when powered by any 802.3at source.. The POE extender can extend the range of the Ethernet network by an additional 100m 328 ft. Extended PoE installation range by additional 100M. The maximum is 6 pieces, 700 meters 2296ft when deployed in cascade.. The PoE Extender cost effective installation - does not require local power and other configuration required. Powered via the PoE input, Plug and Play. Automatically detects and protects PoE equipments from being damaged by incorrect installation..

What it forThe RJ45 combiner carry two 10100 mbps data lines over one Cat5e6 cable for two POE security camera from POE injector or switch, or just to share one single internet cableport for two remote devices. Why need itWith its up-to-date technology, this Ethernet doubler connect two switch ports to one combiner, then the 2-way splitter separates the signal at two devices end , which provides a low cost solution for either use case,save the cost on cables, tubes,installation and time. Simplify connectionThe upgraded version premade with one RJ45-female adapter at the splitter end for easier and securer ethernet cable extension between two camerasdevices,this product just simplifies everything. Network compatibleCompatible with all POE network security surveillance cameraNVR systems and other personal devices that work with 10100 Mbps internet data speed. Long WarranteeTWO years qualtity warranty, local replacement service, 724 standby techni support.

IEEE 802. 3af compliant. Deliver power up to about 328. 1 feet100 meters. Gigabit Ethernet ports. 5912V DC power output. Plug-and-Play - Require no configuration. Industry-leading 2-year and unlimited technical support..

Output Power DC 12V 1.5A 18watts Max., full IEEE 802.3af compliant.. Input Power Voltage DC 44-54V. Data Rate 100100Mbps DC Jack 5.52.1mm. Works with IP camera, IP phone, AP and other 12V Non-PoE devices. Package content 4x PoE splitters.

Run 2 IP Cameras on 1 Cable Allows you to run 1 cable run to the switch for 2 cameras that are near each other. Set consists of a sender unit and a receiver unit. Plug Sender unit into 2 open ports on your POE switch. Run one cable to the location that has the cameras that are nearby each other. Connect 2 short cables to the Receiver unit and connect the other ends to your camera.. Reduces Cabling Costs Lets say you are installing 2 cameras on each side of a corner. Instead of running 2 cables back to the switch, you can now just run 1. Easy and Cost Effective.. Convenient for Adding Camera Ever installed a camera in a location, only to find out that you need another one right by it Whats worse, the switch is on the other side of the building and it took you hours to run that one cable run. No worries Just use this splitter set to make your installation much easier as all you need to do now is run 1 cable from the old camera to the new camera.. Outdoor Waterproof The Receiver Unit comes with weatherproof RJ45 connectors, allowing you to fully expose the Receiver unit to the weather elements.. Easy to UseSimple plug play installation.  Only works on standard POE network switches..

2-PORT POE SPLITTERThis 2-port POE extender is designed to supply POE power to two POE devices through one Cat5E6 cable, and no power adapter is required. It is powered by 48V or 53V PoE SwitchPOE NVRPoE InjectorMid-span. With this POE splitter, users can easily add extra POE device or non-POE device to existing cable without running a new network cable.. UP TO 1,000FT POE DATA EXTENTIONExtra 330ft POEData transmission will be extended with one Linovision POE Extender. And it supports two levels cascade deployment, therefore total 1,000ft POE Data transmission is provided. The 2nd POE Extenders POE Input should be connected to the 1st POE Extenders Out port, not Camera port. COMPLIANT TO IEEE802.3AFAT STANDARDThis POE Extender works with all standard IEEE802.3afat POE SwitchesPOE injectorsPOE NVRs. And the POE Outputs supply power to standard POE devices don't support 24V POE Devices , like POE IP cameraIP phoneIP speaker. Noted The CAMERA Port supports max 8W power consumption and the OUT Port supports max 15W. The max bandwidth is 100Mbps. As the distance increases, the power and the bandwidth will decrease.. EASY TO CONFIGURE IP CAMERA ON SITEBy interting this PoE-Extender02 to an existing PoE cable, installers can use laptop or CCTV Tester to easily adjust camera angle and configure IP. PLUG-N-PLAY INSTALLATIONPlug-n-Play, no configuration or setup is required. With compact dimension 3.1 2 1, enough to fit many junction boxes or outdoor waterproof enclosures..

12V PoE Splitter12V 2A Output,complied with IEEE802.3 af 15Wat30w,IEE 802.3 I, IEEE 802.3 u, IEEE 802.3 x standard.PD support 44V-57V voltage transmission.. Upgrade Isolated VersionThe upgraded isolated version supports short-circuit and overvoltage protection, stable performance, and reduces damage.. Longer Cord VersionThe cable is lengthen to 8 inches,suitable for more situation.. Perfect for SurveillanceThe PoE Splittler is perfect for Security Camera CCTV Surveillance,easy to access Poe network for non-PoE terminal.. After-Sale-ServiceWe committed to provide product- replace- without- repair service..

2 Channel gigabit outdoor PoE extender, easy to extend PoE Power to two PoE devices, such as Wireless APs, Base Stations, Network Cameras or other PoE devices through an exterior network data cable.. IP67 Waterproof, designed for outdoor use. The PoE Extender includes watertight connectors on the input and output ends. With Surge protection and working temperatures of -25C to 55C, it will withstand inclement weather. DO NOT SUBMERGE OR BURY. The input port is IEEE802.3 btataf compliant, which support up to 60 watts PoE power input. While two output PoE ports is 802.3ataf compliant, support to deliver up to 30 watts PoE power per port.. Extends an additional 100m for PoE network. Daisy chain support connect up to 3 PoE Extenders for a total PoE network extension of 400m 1,312 ft... Wall-mount designplug and play, no additional power supply required..