Top 6 Best Pressure Sensor Arduino

The ADXL335 is a small, low profile, low power, complete three-axis accelerometer that provides a signal-conditioned voltage output that measures acceleration over a full 30 g range.. It measures static gravitational acceleration in tilt detection applications as well as dynamic acceleration caused by motion, shock or vibration.. The user selects the bandwidth of the accelerometer using the capacitors X_OUT, Y_OUT, and Z_OUT on the CX, CY, and CZ pins.. The appropriate bandwidth can be selected depending on the application. The X-axis and Y-axis bandwidths range from 0.5 Hz to 1600 Hz, and the Z-axis bandwidth ranges from 0.5 Hz to 550 Hz.. Power supply 35 V, supply current 400uA..

FlexibleBend Sensor The RP-C resistance type pressure sensor is a flexible thin film sensor whose resistance decreases along with the pressure increases. Variable Resistance Single sensitive area pressure sensor is equivalent to a dual port variable resistance whose resistance is controlled by pressure, and to a switch of a certain threshold, the threshold is determined by pressure and equipment parameters setting. Quick Response The pressure sensor supports staticdynamic pressure sensing, and has fast response speed. Premium Quality Material Made of high quality material, the sensor is durable and has long service life. Widely Applications Widely used for bed monitoring, sleep monitoring, smart shoes, smart switches, counters and medical equipment.

Upgarde Pressure Transducer This Pressure Sender is an advance pressure transducer than traditional mechanical pressure transducer. Small Error Offers High Accurate 2FS small output error, including nonlinear, hysteresis error and repeatability, full temperature range. Small Size Provides Convenient Operation Light weight and small size, convenient to install and operate. Widely Applications This Transmitter Sensor has widely applications ,which works for oil, fuel, diesel, gas, water, air pressure, can be used in oil tank, gas tank, diesel tank etc. Protetcion Function It has complete surge voltage protection function.

Great for altitude and weather measurements. Comes with a metal port. Measure absolute pressure 0 to 25 PSI. Compatible with any kind of microcontroller or microcomputer, from an Arduino compatible to Raspberry Pi.

FSR402FA402,FSR408FA408,FSR502FA502 0.5 inch Pressure Sensor Resistance Stress Test Force Sensing Resistor for arduino Diy Kit. This pressure sensor converts the pressure applied in the thin film area of the FSR sensor into the change of resistance value, so as to obtain pressure information.. The higher the pressure, the lower the resistance.. It is allowed to be used at pressure of 100g-10kg.. It can be used in the end gripper of the manipulator to sense the presence or absence of gripping objects, the foot of the bionic robot to walk on the ground, and has a wide range of applications..

BMP180 is a high-precision, small size, ultra-low power pressure sensor that can be used in mobile devices.. The absolute accuracy of the lowest can reach 0.03hPa, and low power consumption, only 3A.. BMP180 uses a powerful 8-pin leadless ceramic chip can be directly connected with a variety of microprocessor via I2C.. Pressure range 300 1100hPa 9000m to -500m. Low power consumption 5A in standard mode. Lead-free, RoHS compliant.

This Kit contains with 3pcs of digital sensor module, which can be independently enabled disabled, which can measure not only the temperature humidity, but also the pressure.. The BME280 sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI.. Our BME280 Sensor is the best low-cost, precision sensing solution for measuring barometric pressure with 1 hPa absolute accuraccy, and temperature with 1.0C accuracy. Because pressure changes with altitude, and the pressure measurements are good, you can also use it as an altimeter with 1 meter accuracy.. BME280 Atmospheric Pressure Sensor Temperature Humidity Sensor Breakout for Arduino. Package 4pcs BME280 Atmospheric Pressure Sensor Temperature Humidity Sensor Breakout.

BMP180 is a high-precision, small size, ultra-low power pressure sensor that can be used in mobile devices. Its performance excellence, the absolute accuracy of the lowest can reach 0.03hPa, and low power consumption, only 3A. BMP180 powerful 8-pin ceramic leadless chip carrier LCC ultra-thin package, you can directly through the I2C bus connected with a variety of microprocessors. Pressure range 300 1100hPa 9000 meters above sea level -500 meters. Low power consumption 5A in standard mode.

100 brand new Pressure transducersendersensor 150 psi stainless steel for oil,fuel,air,water 150 psi Pressure transducersendersensorTransmitter for oilfuelairwater 150 psi oilfuelairwater Pressure transducersendersensorTransmitter, Our material is using top of line 316 stainless steel and high temperature auto-graded plastic.. Output 0.5V4.5V linear voltage output. 0 psi outputs 0.5V, 100 psi outputs 2.5V, 150 psi outputs 4.5V. Pressure MediumThe gas and liquid which is compatible with 316L stainless steel Electromagnetism CompatibilityEN50081-1 EN50082-2 IEC61000-4-3. Interchange Part Number 5VDC. Package include 1 pcs x150 psi pressure transducer.

5 Pack Perfect for Microbit or Aurduino DIY or Educational Kits. FSR402 Sensor with Female Contacts and Housing. Can be used with Alligator Clips or Wires for use with Microbit, microbit, aurduino DIY kits or other school projects. Useful for STEM or STEAM Educators, Classroom Set. Prime Shipping.

The BMP390L has better precision than ever, which makes it excellent for environmental sensing or as a precision altimeter. It can even be used in either I2C and SPI configurations.. This sensor has a relative accuracy of 3 Pascals, which translates to about 0.25 meters of altitude compare to the BMP280's 12 Pascal1 meter and BMP388's 8 Pascal0.5 meter.. The surface-mount sensor is soldered onto a custom made PCB in the STEMMA QT form factor, making them easy to interface with. The STEMMA QT connectors on either side are compatible with the SparkFun Qwiic I2C connectors.. The surface-mount sensor is soldered onto a PCB and comes with a 3.3V regulator and level shifting so you can use it with a 3V or 5V logic microcontroller without worry.. What you will get 1pcs BMP390 module and 2pcs SH1.0 4P cable.