Top 6 Best Ramps 1.4

The fifth stepper motor output port can be customized as a Z-axis motor or a second extruder.. Can be extended to control other accessories.. Three field effect transistors, three heater fan output ports, three thermistor circuits.. Heated bed control, extra 11A fuse.. Pololu board foot socket, can be easily replaced or removed..

The RAMPS1.4A is used as driving shield for 3D printers, it is easy to stack it onto the MEGA 2560 control board.. It has total 5 slots for stepper motor drive module to drive 5-channel stepper motors. The slots are compatible with all kinds of drive modules like A4988, DEV8825.. There are 3 jumper caps under each slot, which can be used to control the working subdivision of drive modules.. For example, if connect the A4988 and plug three jumpers, the subdivision port MS1MS2 and MS3 of A4988 module are at active HIGH, so the A4988 module is in 16-subdivision working mode.. But if unplug the three jumpers, MS1MS2 and MS3 of A4988 module are at active LOW, so the A4988 module is in full-step working mode..

Suitable for 5 Pololu stepper drive boards.. The fifth stepper motor output port can be customized as a Z-axis motor or a second extruder.. RAMPS 1.4 Control Panel is used as driving shield for 3D printers, and it's easy to stack it onto the MEGA 2560 control board.. The fifth stepper motor output port can be customized as a Z-axis motor or a second extruder.Pololu board foot socket, can be easily replaced or removed.. Fully assembled and tested, no soldering required. It is designed to fit all the electronics needed for a RepRap in a small package. Modular design includes plug-in stepper drivers and extruder control electronics on an for Arduino MEGA shield for easy service, parts replacement, upgrade-capacity and expansion.

2560 control board The board is a microcontroller board based on the 16AU .It has 54 digital inputoutput pins of which 14 can be used as PWM outputs, 16 analog inputs, 4 UARTs hardware serial ports, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.. RAMPS 1.4 RAMPS interfaces an for Arduino with the powerful for Arduino platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an for Arduino shield for easy service, part replacement, upgrade-ability and expansion. for Additionally, a number of for Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.. LCD 12864 with Controller This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the smart adapter included.. A4988 driver module A4988 Stepper Motor Driver Board is a breakout board for Allegros A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection please read the A4988 datasheet carefullybefore using this product.. Warning Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. More generally, rewiring anything while it is powered isasking for trouble..

INSTRUCTIONSThe RAMPS 1.4 board is designed to fit the entire electronics needed for a RepRap in one small package for low cost. HAS PLENTY ROOM FOR EXPANSIONRAMPS interfaces an Mega with the powerful MEGA platform and has plenty room for expansion. MODULAR DESIGNThe modular design includes plug in stepper drivers and extruder control electronics on an MEGA shield for easy service, part replacement, upgrade-ability and expansion. NOTEAdditionally, a number of expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack. WITH THE BOOT-LOADERWith the boot-loader, download the program directly via USB without having to go through other external writer.

Exquisite design-- The RAMPS 1.4 board is designed to fit the entire electronics needed for a RepRap in one small package for low cost.. Broad expansion-- RAMPS interfaces an Mega with the powerful MEGA platform and has plenty room for expansion.. Easy to Use-- The modular design includes plug in stepper drivers and extruder control electronics on an MEGA shield for easy service, part replacement, upgrade-ability and expansion.. Multifunction-- Additionally, a number of expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.. Excelent Performance-- Mega is an ATmega2560 as core micro-controller development board itself has 54 groups digital I O input output terminal 14 groups do PWM outputs, 16 sets of simulation than the input side, group 4 UARTs hardware serial ports, using the 16 MHz crystal oscillator..

3D Printer Controller RAMPS 1.4 interfaces a Compatible Arduino Mega2560 board. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion. 3D Printer Controller RAMPS 1.4 interfaces a Compatible Arduino Mega2560 board. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion. With LCD 12864, you can easy connect it to your Ramps board using the smart adapter included. After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. Please Note No technical support for this product..

Package includes 5 pieces..

Adjustable current control lets you set the maximum current output with a potentiometer. Simple step and direction control interface.Five different step resolutions full-step, half-step, quarter-step,eighth-step, and sixteenth-step. Thermal protection,under-voltage lockout,and crossover-current protection,ground fault protection. Intelligent chopping control that automatically selects the correct current decay mode fast decay or slow decay. widely used in 3D printers and small CNC machines.

Latest CH340G CNC Shield expansion board Version 3. 0 for Arduino. Kuman Board, MCU ATmega328, USB interface ATmega16U2 with 1. 5m USB Cable. 4pcs DRV8825 Stepper Motor Driver with heat sinks. 3pcs NEMA-17 Stepper Motor 84 oz. in 59 Ncm 47mm Body 1. 8 degree with mounting Bracket Kit DIY CNC Robot with 3pcs Mounting Bracket and 12 pcs M3 Screws. 3pcs End stop Mechanical Limit Switches for RAMPS 1. 4 with 3Pin 70cm Cable.