Top 6 Best Springfield Xd Sights

New design in 2020. This brand new designed optic mounting plate is to REPLACE the rear sight of pistol. Specially made to fit Springfield XD, XD MOD.2, XDM, XDS Pistol. Does not fit 5.25 XDM competition series. It is design to for Springfield Non-OSPNon Optics Ready XDXDSXDM pistols that do NOT has a Optic Cut. This plate is for replacing rear sight. It also fits Non-OSP Hellcat. It does NOT fit 5.25 XDM competition series. This new plate is an re-designed version to replace the old E1E2 plate for Springfield xd that always need modification caused by incorrect dovetail size.. Fit Ade RD3-006AHuracan, RD3-006BCobra, RD3-009Crusader, RD3-012Delta, RD3-013Bertrillium, RD3-015ZantitiumRed dots. Also Fit Vortex VenomRazorViper, Burris Fastfire, Meopta, Eotech MRDS, Docter, Insight, Sightmark Minishot.. There are two parts of this plate. This Small Dovetail Insert plate basically replaces the rear sight using two jam screws. The big plate uses two silver alignment pins at 2 of the 4 corner holes for the optic to sit in.. Hiring a gunsmith is highly recommended, Unprofessional installation such as improper torque will result in screw loose, not holding zero, damage to the firearmoptic and personal injury. Machined from aircraft grade aluminum with hard anodizing finish. Comes with screws and hardware for instsallation. Including two align pins to attach to any of the four corner holes to prevent any movement..

Comes with a Picaitnny mount. Also comes with ADE all new designed adapter mount for Springfield XD, XDE 3.8XD MOD.2, XD3.33.8 Single Stack, XDM, Hellcat Non-OSP Pistol. It does NOT fit 5.25 XDM competition series, it does NOT fit any OSP optics ready models. While it is possible to install this mount without the use of a Gunsmith, we recommend hiring a professional gunsmith. Please note. Unprofessional installation such as improper torque will result in screw loose, not holding zero, damage to the firearmoptic and personal injury.. Bertrillium RD3-013 Red Dot. New advanced battery technology gives up to 2000 hours on bright setting and up to 30k hours on Low setting with a 1632 BatteryIncluded. 4 MOA dot.Red dot DOES NOT auto power off. It stays on til use manually power off. It has multi brightness level with one adjustment button. Every time you turn on the dot it stays the same B rightness level last time it was turned off. The lowest setting is invisible by human Eye that is for using with a night vision. Top load System, no need to Remove the sight to change the Battery and re-sight in to waste ammo. Promotes rapid target acquisition while providing a precise point of aim getting shots down range and on target fast..

Does NOT fit the new HELLCAT OSP. Fits directly on Springfield XDM XD-M OSP system with the 1 mount that comes with OSP without needing to remove the rear sight. This optics does NOT fit XDMXDXDS, it only fits xdm OSP models which are the springfield's newest Optics Ready Pistols.. Red dot has multi brightness level with one adjustment button. Every time you turn on the dot it stays the same brightness level last time it was turned off. Promotes rapid target acquisition while providing a precise point of aim getting shots down range and on target fast. Top load System, no need to Remove the sight to change the Battery. 6 MOA dot. Come with Protected Cover, Adjustment wrench, Adjustment dailing plate, User Manual and Picatinny mounting plate.. 1.75 length x1.25 width x1.15 height. Shockproof, Fogproof and waterproof for 30 minutes under 4ft water.Feature 1 M.O.A wind age and elevation adjustments with audible click. This listing only comes with a picatinny plate.If user has a Springfield OSPoptics ready model that has a optic cut in front of the rear sight, user need to obtain Springfield provided 01 plate.The springfield official Sku is XD5071, you can obtain that plate from springfield for free. If user has a Non-OSPnon-optics ready XD, XD MOD.2, XDM, XDS Pistol, user need to purchase an aftermarket optic plate to replace the rear sight, please search amazon Item Number B087H5GHCR for the plate..

FDE Offers the brightest Green laser allowed by Law. Non-handheld class 3R laser product, 5Mw power output. Ultra lightweight and compact 1.79L x 1.06W x .85H. Fit rail-equipped pistols, rifles and shotguns. The laser sight fits onto virtually any firearm with a modern M1913 Pica tinny or Weaver-style accessory rail. For pistols that does NOT has a raildovetail slot under the barrel such as Sig P365, user need to obtain a rail adapter for the laser to fit.. Proprietary mounting design provides two spring loaded pillar to push to rail slot for rock solid zero movement. Weight 1.13oz Battery included. Does NOT fits Berreta due to extra wide trigger guard.. Operates with one CR13N batteriesincluded. Battery life 1 hours. The unit is quickly and easily, user-installed in moments and can be painlessly transferred from firearm to firearm. Controlled by ambidextrous switch. It offers two modes constant-on and strobe. This allows the user to easily set their mode based on personal need or preference.

Flat Dark Earth body color Offers the brightest RED laser allowed by Law. Non-handheld class 3R laser product, 5Mw power output. Ultra lightweight and compact 1.79L x 1.06W x .85H. Fit rail-equipped pistols, rifles and shotguns. The RED laser sight fits onto virtually any firearm with a modern M1913 Pica tinny or Weaver-style accessory rail. Pat Pending mounting design provides two spring loaded pillar to push to rail slot for rock solid zero movement. Weight 1.13oz Battery included. Does NOT fits Berreta due to extra wide trigger guard.. Operates with one CR13N batteriesincluded. Battery life 1 hours. The unit is quickly and easily, user-installed in moments and can be painlessly transferred from firearm to firearm. Controlled by ambidextrous switch. It offers two modes constant-on and strobe. This allows the user to easily set their mode based on personal need or preference.

This is RD3-012G is GREEN DOT model, there is also a RD3-012 Red dot. The sight has multi brightness level with TWO adjustment button. One to turn bright up and one to turn down. Hold the down button for 3 secs to power off. Every time you turn on the dot it stays the same brightness level last time it was turned off. Does NOT fit the new HELLCAT OSP. Fits directly on Springfield XDM XD-M OSP system with the 1 mount that comes with OSP without needing to remove the rear sight. This optics does NOT fit XDMXDXDS, it only fits XDM OSP models which are the springfield's newest Optics Ready Pistols.. Promotes rapid target acquisition while providing a precise point of aim getting shots down range and on target fast. Top load System, no need to Remove the sight to change the Battery that requires re-sight in and waste ammo.. GREEN dot has multi brightness level with one adjustment button. Every time you turn on the dot it stays the same brightness level last time it was turned off. 6 MOA dot. Come with Protected Cover, Adjustment wrench, Adjustment dailing plate, User Manual and Picatinny mounting plate. Additional mounting plates for hunguns sells separately. This listing only comes with a picatinny plate.If user has a Springfield OSPoptics ready model that has a optic cut in front of the rear sight, user need to obtain Springfield provided 01 plate.The springfield official Sku is XD5071, you can obtain that plate from springfield for free. If user has a Non-OSPnon-optics ready XD, XD MOD.2, XDM, XDS Pistol, user need to purchase an aftermarket optic plate to replace the rear sight, please search amazon Item Number B087H5GHCR for the plate..

Designed to fit Canik Elite TP9 SC, Canik METE SFX, Canik METE SFT, Sig P365XP365XLP365XL SPECTRE COMP, Ruger Max-9, Glock 43X MOS48 MOSnot compatible with regular glock 43x48 that are not MOS, Springfield Hellcat OSP, SW Shield 2.0 Optics Ready, SW MP9 EZ, SW MP shield plus performance center, Walther PPS M2 Optics Ready, Girsan MC1911SC Ultimate or any pistolmounting plateslide with RMSRMSC screw patternfootprint.. Hard coated aircraft aluminum and multi-coated glass. Not plastic body with polymer lens.. ADE SPIKE red dot sight is always powered on with automatic brightness. Operates with a single CR2032 3v battery. With our advanced technology the sight only draws approximate 700 microampere powers to give a very long battery life. The brightness will turn high and low accordingly to the environment brightness.. 4MOA, Weight approximately 17.6 grames0.62oz, Length1.6 x Width.92 x Height.93. Comes with screws for several Optics Ready handguns. Does not comes with any mounting plate such as picatinny mount or plate made for a specific handgun.. Ade SPIKE created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distancegap on some full size optics ready pistols, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight. For non-optics ready pistols that need to use an optic plateadapter to replace the pistol manufacturer equipped rear sight, ADE Spike's rear white dot will act as a pistol factory original rear sight for Co-Witness.. Comes with 3 pairs of screws for Sig P365XLX, Springfield Hellcat OSP and Canik TP9 Elite SC ONLY. The provided screws might NOT work with EVERY compatible pistol listed. ADE makes the red dot to accept the industrial standard footprint. The pistol manufacturer makes the optic cutslide for the same footprint, but they have their own opinions to decide which type screws that the screw holes take.. ADE Does not know the screw spec every pistol manufacture used for their screw hole. Please ask the pistol manufacture what screw specs they used on the hole and ask them to provide the screw. If you cant get the screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size..

This is ADE's new GREEN dot version of RD3-018 Spike. The Spike now available in 3 models. Black body 4MOA Red dot, Black body 4MOA GREEN dotthis one and FDETAN body 4MOA Red dot.. Designed to fit Canik Elite TP9 SC, Canik METE SFX, Canik METE SFT, Sig P365XLP365X, Ruger Max-9, Glock 43X MOS48 MOSnot compatible with regular glock 43x48 that are not MOS, Springfield Hellcat OSP, SW Shield 2.0 Optics Ready, SW MP9 EZ, SW MP shield plus performance center, Walther PPS M2 Optics Ready, Girsan MC1911SC Ultimate or any pistolmounting plateslide with RMSRMSC screw patternfootprint.. Hard coated aircraft aluminum and multi-coated glass. Not plastic body with polymer lens.. ADE SPIKE red dot sight is always powered on with automatic brightness. Operates with a single CR2032 3v battery. With our advanced technology the sight only draws approximate 700 microampere powers to give a very long battery life. The brightness will turn high and low accordingly to the environment brightness.. 4MOA, Weight approximately 17.6 grames0.62oz, Length1.6 x Width.92 x Height.93. Ade SPIKE created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distancegap on some full size optics ready pistols, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight. For non-optics ready pistols that need to use an optic plateadapter to replace the pistol manufacturer equipped rear sight, ADE Spike's rear white dot will act as a pistol factory original rear sight for Co-Witness.. Comes with screws for several Optics Ready handguns. Does not comes with any mounting plate such as picatinny mount or plate made for a specific handgun.. Comes with 3 pairs of screws for Sig P365XLX, Springfield Hellcat OSP and Canik TP9 Elite SC ONLY. The provided screws might NOT work with EVERY compatible pistol listed. ADE makes the red dot to accept the industrial standard footprint. The pistol manufacturer makes the optic cutslide for the same footprint, but they have their own opinions to decide which type screws that the screw holes take.. ADE Does not know the screw spec every pistol manufacture used for their screw hole. Please ask the pistol manufacture what screw specs they used on the hole and ask them to provide the screw. If you cant get the screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size..

Comes with a Picaitnny mount. Also comes with ADE all new designed adapter mount for Springfield XD, XDE 3.8XD MOD.2, XD3.33.8 Single Stack, XDM, Hellcat Non-OSP Pistol. It does NOT fit 5.25 XDM competition series, it does NOT fit any OSP optics ready models. While it is possible to install this mount without the use of a Gunsmith, we recommend hiring a professional gunsmith. Please note. Unprofessional installation such as improper torque will result in screw loose, not holding zero, damage to the firearmoptic and personal injury.. Zantitium RD3-015 Red Dot. New advanced battery technology gives up to 3000 hours on bright setting and up to 40k hours on Low setting with a CR2032 BatteryIncluded. The biggest handgun sight on the market Actual size is. 2.25 Length x 1.4 Width x 1.27 Height.For reference, vortex venom is 1.9Lx1.11Wx1.02H. It gives up to twice bigger window than other micro red dot.. Top load System, no need to Remove the sight to change the Battery and re-sight in to waste ammo.4 MOA dot.Red dot DOES NOT auto power off. It stays on til use manually power off. It has multi brightness level with one adjustment button. Every time you turn on the dot it stays the same B rightness level last time it was turned off. The lowest setting is invisible by human Eye that is for using with a night vision.

Comes with mounting plate for Springfield XD and also a standard picatinny mount. Does NOT fits XDS, XDM.. We have made several improvements since it's initial release in 2016. We have made it more durable to withstand various recoil and improved the ability to hold zero. Designed in Oregon.. WaterproofShockFog Resistant. Lenses are precision ground and polished to exacting geometries to virtually eliminate parallax and to provide a very clear, crisp sight picture.. Fully windage and elevation adjustable and lockable Unlimited Eye Relief. 5 MOA. 5 Illumination Settings. Powered by a lithium CR2032 batteryIncluded.

Does NOT fit the new HELLCAT OSP. Fits directly on Springfield XDM XD-M OSP system with the 1 mount springfield sku XD5071 that comes with OSP without needing to remove the rear sight. This optics does NOT fit XDMXDXDS, it only fits xdm OSP models which are the springfield's newest Optics Ready Pistols.. For Non-OSP XDMXDXDS models, this red dot need a red dot mount to replace the rear sight. Search amazon item B087H5GHCR for the plate. Every time you turn on the dot it stays the same B rightness level last time it was turned off. The lowest setting is invisible by human Eye that is for using with a night vision. Promotes rapid target acquisition while providing a precise point of aim getting shots down range and on target fast. Top load System, no need to Remove the sight to change the Battery. New advanced battery technology gives up to 2000 hours on bright setting and up to 30k hours on Low setting with a 1632 BatteryIncluded. Come with a mounting plate for picatinny rail.. 4 MOA dot.Red dot DOES NOT auto power off. It stays on til use manually power off. It has multi brightness level with one adjustment button.. This listing only comes with a picatinny plate.If user has a Springfield OSPoptics ready model that has a optic cut in front of the rear sight, user need to obtain Springfield provided 01 plate.The springfield official Sku is XD5071, you can obtain that plate from springfield for free. If user has a Non-OSPnon-optics ready XD, XD MOD.2, XDM, XDS Pistol, user need to purchase an aftermarket optic plate to replace the rear sight, please search amazon Item Number B087H5GHCR for the plate..

Fits Springfield XD Series XD, XDS, XDE, XDM excluding 5.25 Comp Series. Brightness and durability of our original Tritium sights, but with added Pro-level features Tritium night sights transition from standard white dot sights during the daylight, to glowing green dots in the the dark. Utilizes quality Swiss tritium for maximum brightness and unmatched visibility in all shooting conditions 247 Glows in the dark with no batteries or light sources needed. Front sight features a highly visible white Focus-Lock ring surrounding the front fiber to make it even more visible, encouraging the eye to rapidly focus on the front sight for a fast and accurate sight picture. Compact design maintains factory sight radius and fits standard holsters Angled rear sight edge for emergency onehand operation.

SF XD Set DayNight Sight, Orange. Contrasting colored front sight ring for even faster focus. Quick and accurate U-notch Design. Angled rear sight edge for emergency one-hand operation. All features of our popular TFX Handgun sights. FORTRESS FINISH provides a permanent protective coating for maximum protection. Black Retention Rings improve front sight acquisition and reduce glare. Sport type Hunting.

UNMATCHED VISIBILITY in all shooting conditions, night or day GLOWS IN THE DARKno batteries or light exposure required. Available with YOUR CHOICE of GREEN OR YELLOW FIBER in rear sights Yellow fibers in the rear sight increase contrast and aid in quickly focusing on the brighter green front sight. Made of tough, CNC-machined steel with a FORTRESS FINISH COATING for maximum protection. CONCEALED FIBER cannot be seen by target SNAG RESISTANT DESIGN fits standard holsters. Fits Springfield XD, XDM excluding 5.25 Comp Series and XDS.

Fits Springfield XD Series XD, XDS, XDE, XDM excluding 5.25 Comp Series. Fiber-optics for the brightest aiming points even in low-light conditions Tri-Dot aiming system of contrasting front and rear colors. Concealed fiber cannot be seen by target Snag resistant design fits standard holsters. Fortress-Finish coating provides a permanent protective coating for maximum protection. Machined and assembled in the USA Made of tough, CNC-machined steel.

SUPERIOR AIM Pistol sight ideal for getting a better look at your target and always taking the perfect shot. GLOW-IN-THE-DARK Glow-in-the-dark feature allows your sight to glow bright both day and night, ensuring you have a clear sight picture. FORTRESS FINISH Provides a permanent protective coating for maximum protection and concealed fiber that cannot be seen by the target. INTUITIVE DESIGN Quick and accurate Square-notch design Angled rear sight edge for emergency one-hand operation. SPECIFICATIONS Springfield XD, XDM excluding 5.25 Comp Series, and XDS.

Fits Springfield XD Series XD, XDS, XDE, XDM excluding 5.25 Comp Series. Fully protected TFO technology encapsulated in a virtually indestructible configuration Impervious to oils, chemicals, cleaning solvents and ultra-sonic cleaning processes. Utilizes quality Swiss tritium for maximum brightness and unmatched visibility in all shooting conditions 247 Glows in the dark with no batteries or light sources needed. Front sight features a highly visible white Focus-Lock ring surrounding the front fiber to make it even more visible, encouraging the eye to rapidly focus on the front sight for a fast and accurate sight picture. Concealed fiber can not be seen by target Fortress-Finish provides a permanent protective coating for maximum protection Features a snag resistant design and fits standard holsters.

Product Type Sporting Goods. Item Package Dimensions 2.54 L X 9.525 W X 13.97 H Cm. Country Of Origin United States. Item Package Weight 0.027 kgs.

Highly Accurate Sights Precision-engineered for accuracy, the set of 2 pistol sights ensures you consistently hit your target with ease, enhancing your shooting experience. Day and Night Visibility Featuring glow-in-the-dark elements, these sights remain visible even in low-light conditions, enabling you to maintain accuracy both during the day and at night. Seamless Holstering Designed with a compact profile, these sights seamlessly holster and draw from standard holsters, eliminating the risk of catching or snagging during critical moments. Single-Handed Precision Angled rear sight edge allows for precise aiming even with one hand, empowering you to maintain accuracy and control in various shooting scenarios. Wide Compatibility Compatible gun models include Springfield XD, XDM excluding 5.25-inch Comp Series, and XDS Quick and accurate square-notch design.