Top 6 Best Stabilus Lift-o-mat

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT SEE PICTURE Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head little plastic end, to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5 size variation.. Truck Upfitters Pair of 38 pound each gas struts. 15.7 extended length and 9.4 compressed length. This size of door shock absorber is for tall medium weight rear or side camper shell doors. Each canopy shock has 38 lbs of pressure, for a total of 76 lbs of pressure. Please note that this does not mean that it can lift something that is 76 lbs. the typical hinged-style door weight for this prop is approximately 50-70 lbs, including the weight of the camper shell locks and keys.. These gas lift cylinders do not fit all truck capcamper shell brandsmodels. Measure your strut from center of socket to center of socket when fully opened fully closed to get accurate measurement. See pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.. Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.. Equivalent to Suspa c16-09209 or Stabilus 01824. These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Glasstite parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks gas springs gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect fit for your topper.

Effortless opening of doors and lids. Softer and quieter closing. Smooth motion and stopping.. Secure holding in open and closed positions. Easy to mountinstall. Maintenance free.. Compact and attractive design. Opens to 90 Degrees. One pair does one door.. Maximum door height 24.

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL TOPS THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT SEE PICTURE Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head little plastic end, to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5 size variation.. Truck Upfitters Pair of 55 pound each gas struts. 15.7 extended length and 9.4 compressed length. This size of door shock absorber is for tall mediumheavy weight rear or side camper shell doors. Each canopy shock has 55 lbs of pressure, for a total of 110 lbs of pressure. Please note that this does not mean that it can lift something that is 110 lbs. the typical hinged-style door weight for this prop is approximately 70-90 lbs, including the weight of the camper shell locks and keys.. These gas lift cylinders do not fit all camper shell brands models. Measure your strut from center of socket to center of socket when fully opened fully closed to get accurate measurement. Please see pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.. Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.. Compatible with Suspa c16-23994 compatible with Stabilus 025657 These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks gas springs gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect fit for your topper.

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT SEE PICTURE Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head little plastic end, to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5 size variation.. Truck Upfitters Pair of 45 pound each gas struts. 15.7 extended length and 9.4 compressed length. This size of door shock absorber is for medium height and weight rear or side camper shell doors. Each canopy shock has 45 lbs of pressure, for a total of 90 lbs of pressure. Please note that this does not mean that it can lift something that is 90 lbs. the typical hinged-style door weight for this prop is approximately 60-80 lbs, including the weight of the camper shell locks and keys.. These gas lift cylinders do not fit all camper shell brands models. Measure your strut from center of socket to center of socket when fully opened fully closed to get accurate measurement. Please see pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.. Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.. Equivalent to Suspa c16-23993 or Stabilus 14269. These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Glasstite parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks gas springs gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect fit for your topper.

This listing includes 2 Lift Supports for Multi Purpose Applications.. Extended Length from Center Mount to Center Mount is 26.5 in.. Lift Supports Depot supports are High Quality European Lift Struts. Designed to install easily in minutes, often times without special tools.. Installs easy with no special tools required.. Compatible with the following OEM Numbers 654150,PM3888.

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT SEE PICTURE Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head little plastic end, to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5 size variation.. Truck Upfitters Pair of 45 pound each gas struts. 17.1 extended length and 9.9 compressed length. This size of door shock absorber is for tall medium weight rear or side camper shell doors. Each canopy shock has 45 lbs of pressure, for a total of 90 lbs of pressure. Please note that this does not mean that these gas lift shocks can lift something that is 90 lbs. the typical hinged-style door weight for this prop is approx 60-80 lbs, including the weight of the camper shell locks keys.. These gas lift cylinders do not fit all camper shell brands models. Measure your strut from center of socket to center of socket when fully opened fully closed to get accurate measurement. Please see pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.. Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.. Equivalent to Suspa C16-04270 or Stabilus 1822. These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Glasstite parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks gas springs gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect fit for your topper.

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT SEE PICTURE Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head little plastic end, to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5 size variation.. Truck Upfitters Pair 2 total of 24 pound each gas struts. 12.2 extended length and 8.6 compressed length. This size of door shock absorber is for tall medium weight rear or side camper shell doors. Each canopy shock has 24 lbs of pressure, for a total of 48 lbs of pressure. Please note that this does not mean that it can lift something that is 48 lbs. the typical hinged-style door weight for this prop is approximately 20-40 lbs, including the weight of the camper shell locks and keys.. These gas lift cylinders do not fit all truck capcamper shell brandsmodels. Measure your strut from center of socket to center of socket when fully opened fully closed to get accurate measurement. See pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.. Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.. Equivalent to Suspa C16-03795 or Stabilus 1906. These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Glasstite parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks gas springs gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect fit for your topper.

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT SEE PICTURE Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head little plastic end, to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5 size variation.. Truck Upfitters Pair 2 total of 40 pound each gas struts. 12.2 extended length and 7.5 compressed length. This size of door shock absorber is for tall medium weight rear or side camper shell doors. Each canopy shock has 40 lbs of pressure, for a total of 80 lbs of pressure. Please note that this does not mean that it can lift something that is 80 lbs. the typical hinged-style door weight for this prop is approximately 50-70 lbs, including the weight of the camper shell locks and keys.. These gas lift cylinders do not fit all camper shell brands models. Measure your strut from center of socket to center of socket when fully opened fully closed to get accurate measurement. Please see pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.. Equivalent to Suspa C16-11028, Stabilus 19068, or Weatherguard 7009-2PK . Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper canopy windoors, RV doors awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, other toolbox struts, etc. These gas shock lift supports CAN'T be compressed by hand. They MUST be installed in the EXTENDED OPEN position. It is nearly impossible to install them in the CLOSED position.. NOT FOR STEEL TOOLBOXES- WILL NOT HOLD UP LID. Fit most Weatherguard ALUMINUM truck bed toolboxes ONLY, models 121-0-01, 121-5-01, 123-0-01, 123-5-01, 127-0-01, 127-5-01, 131-0-01, 131-5-01, 137-0-01, 137-5-01, 147-0-01, 147-5-01, 154-0-01, 154-5-01. Compatible with many truck canopy types, including LEER, ARE, Century, Snugtop, and ATC tops, many other brands that utilize gas shocks gas springs gas lifts. Compatible with many gas lift brands, including stabilus, lift o mat, Suspa..

Most used for 16 45lb gas shock struts fit for Leer ARE camper shell topper rear window bed Cover, other custom applications such as cabinet door, outdoor bench lid, toolbox, boat lid, tarp door and so on.. Parameter Compressed Length Center-to-Center 9.4in 239mm. Extended Length Center-to-Center 15.7in 399mm. Force 45 Lbs200N per Strut. Please measure the length of your original shocks before purchasing.. Tips Tips for gas spring used on custom applications. If your lid or door weighs 20-40lb, just install ONE. The lid or door weighs 50-85lb, install both. If you are not sure, please contact us before buying, we will provide you with professional advice.. Content Package arrive with 10mm ball mounting bracket and nut x 4, gas shock x 2.. 121 MONTH REPLACEMENT SERVICE Welcome to Click Ask Seller BESIDE YOUR ORDER for In-time Assistance if any problem occurs..

Application Range -- Most suitable support weight for 2 struts is between 44lb to 61lb If your lid weighs between 25lb to 30lb, you can only install ONE If out of this range, please choose OTHER PRESSURE ARANA struts if you need such struts with mounting brackets, please search B08P38MVQT. Specification -- 2Pcs Set Force 55 lbs 245N Per Shock Force 110 lbs 490N Per Set Extended Length A in 17.20, Compressed Length B in 10.60, End Fittings 10mm Nylon Ball SocketsNote DO NOT compress them by hands before installing, the struts could only be compressed after installing successfully. Function -- This Set of 2pcs 17 Lift Supports could be used on your ARE ATC Leer Camper Shell Awning Snugtop Topper Canopy Truck Cap Pickup Window RV door or Toolbox Lid etc.. Fitment Number -- Interchange number 1595EY, 4514, 8195565, AH8650, ML1650, ML16-50, ML-16-50, ML3650, ML36-50, ML-36-50, P2032, SE172P55,SE618A45PS130PM3, SE630V-55, SL1650, SL16-50, SL-1650, SL-16-50, SL16501, SL16-50-1, SL-16501,SL-16-50-1, SL16505, SL16-50-5, SL-16505, SL-16-50-5, SL3650, SL36-50, SL-3650. How to Message us -- If any missing partspressure unfit or received WRONG-SIZE product, please DO click ASK SELLER besides your order from us, we will send out a new correct package at the soonest without your returning the last set.