Top 6 Best Swampfox Red Dot

Designed to fit Canik Elite TP9 SC, Canik METE SFX, Canik METE SFT, Sig P365XP365XLP365XL SPECTRE COMP, Ruger Max-9, Glock 43X MOS48 MOSnot compatible with regular glock 43x48 that are not MOS, Springfield Hellcat OSP, SW Shield 2.0 Optics Ready, SW MP9 EZ, SW MP shield plus performance center, Walther PPS M2 Optics Ready, Girsan MC1911SC Ultimate or any pistolmounting plateslide with RMSRMSC screw patternfootprint.. Hard coated aircraft aluminum and multi-coated glass. Not plastic body with polymer lens.. ADE SPIKE red dot sight is always powered on with automatic brightness. Operates with a single CR2032 3v battery. With our advanced technology the sight only draws approximate 700 microampere powers to give a very long battery life. The brightness will turn high and low accordingly to the environment brightness.. 4MOA, Weight approximately 17.6 grames0.62oz, Length1.6 x Width.92 x Height.93. Comes with screws for several Optics Ready handguns. Does not comes with any mounting plate such as picatinny mount or plate made for a specific handgun.. Ade SPIKE created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distancegap on some full size optics ready pistols, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight. For non-optics ready pistols that need to use an optic plateadapter to replace the pistol manufacturer equipped rear sight, ADE Spike's rear white dot will act as a pistol factory original rear sight for Co-Witness.. Comes with 3 pairs of screws for Sig P365XLX, Springfield Hellcat OSP and Canik TP9 Elite SC ONLY. The provided screws might NOT work with EVERY compatible pistol listed. ADE makes the red dot to accept the industrial standard footprint. The pistol manufacturer makes the optic cutslide for the same footprint, but they have their own opinions to decide which type screws that the screw holes take.. ADE Does not know the screw spec every pistol manufacture used for their screw hole. Please ask the pistol manufacture what screw specs they used on the hole and ask them to provide the screw. If you cant get the screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size..

Designed to fit Canik Elite TP9 SC, Canik METE SFX, Canik METE SFT, Sig P365XP365XLP365XL SPECTRE COMP, Ruger Max-9, Glock 43X MOS48 MOSnot compatible with regular glock 43x48 that are not MOS, Springfield Hellcat OSP, SW Shield 2.0 Optics Ready, SW MP9 EZ, SW MP shield plus performance center, Walther PPS M2 Optics Ready, Girsan MC1911SC Ultimate or any pistolmounting plateslide with RMSRMSC screw patternfootprint.. Hard coated aircraft aluminum and multi-coated glass. Not plastic body with polymer lens.. ADE SPIKE red dot sight is always powered on with automatic brightness. Operates with a single CR2032 3v battery. With our advanced technology the sight only draws approximate 700 microampere powers to give a very long battery life. The brightness will turn high and low accordingly to the environment brightness.. 4MOA, Weight approximately 17.6 grames0.62oz, Length1.6 x Width.92 x Height.93. Comes with screws for several Optics Ready handguns. Does not comes with any mounting plate such as picatinny mount or plate made for a specific handgun.. Ade SPIKE created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distancegap on some full size optics ready pistols, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight. For non-optics ready pistols that need to use an optic plateadapter to replace the pistol manufacturer equipped rear sight, ADE Spike's rear white dot will act as a pistol factory original rear sight for Co-Witness.. Comes with 3 pairs of screws for Sig P365XLX, Springfield Hellcat OSP and Canik TP9 Elite SC ONLY. The provided screws might NOT work with EVERY compatible pistol listed. ADE makes the red dot to accept the industrial standard footprint. The pistol manufacturer makes the optic cutslide for the same footprint, but they have their own opinions to decide which type screws that the screw holes take.. ADE Does not know the screw spec every pistol manufacture used for their screw hole. Please ask the pistol manufacture what screw specs they used on the hole and ask them to provide the screw. If you cant get the screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size..

Do not return your defective red dot that can't adjust the illuminated dot high enough to zero. This optic shim solves the problem by raising the red dot higher to zero. Optic Shim is made to fit between the red dot and the mounting plate.. Fits Trijicon RMRSRO, Ade Advanced Optics, RD3-019, RD3-020, RD3-023, Holosun HS407CHS507CHS507T and. Also fits Riton X3 Tactix PRD, ADE RD3-011, Swampox KingslayerLibertyJustice. The shim might need to be trimmed to the shape to match some of red dot brand mentioned above.. What it does While zeroing the red dot sight, some users turned the elevation screw all the way to the end that can no longer turnscrew maxed-out, the location of the illuminated dot is still TOO HIGH, user is UNABLE to adjust the dot LOW enough to zero. Instead of returning the defective red dot, this shim will rise the optic to help user to move the illuminated dot higher to the location to zero. Scope base shims Tolerance -.005 Taper 1.0 degree.. Depending on the handgun, some handguns need THIS 1degree shim to give extra range of elevation across a wide range of firearms such as the 1911. Should you feel any resistance from the mechanism whilst zeroing the elevation please fit the shim between the sight and the mount with the thickest part at the rear..

Choose from 3 MOA dot, red circle dot, or green circle dot reticles. RMR footprint scope base for maximum compatibility with pistol slides and included low picatinny mount. Uses CR1632 battery, Change via side tray with no optic re-zero needed with Auto shut off after 4 hours with no movement UP button to wake. 13 illumination settings to match your needs. Weighs only 1 oz in pistol configuration, 1.3 oz with rifle or gun mount. Dimensions 1.8L 1 W and 1.4 H using the long gun mount.

DUTY GRADE DARN RIGHT Other companies are producing slimline pistol dots with plastic bodies and clear polymer lenses. Thats not our style. Sentinel is crafted from CNC machined 7075-T6 aluminum, hard coated in matte black, and features multicoated glass of the same excellent quality used in our long-range precision rifle scopes.. BUT WHAT DOES IT FIT Sentinel is really small. About an inch tall, an inch wide, and 1.6 inches long. Shoehorned into this tiny scope is a 16mm x 16mm window, big enough for fast acquisition and sight tracking, small enough that it doesnt affect concealment at all. Sentinel will any slimline slide with an RMSc footprint incorporated.. BET YOUR SS DEPENDABLE A concealed carry optic must be ultra dependable, because you are literally betting your life that it will be ready when called upon. Sentinel is dunk it waterproof when installed using the included flexible seal that fits between the optic and footprint. It is shock rated to an incredible 1500 G.. MANUAL VS. AUTOMATIC, THE CHOICE IS YOURS Sentinel-M manual features ten manually adjusted brightness settings accessed via digital push buttons. Shake N Wake motion sensing preserves battery life when Sentinel-M has been still for about 4 minutes. With new motion, Sentinel-M resumes its previous brightness level.. Sentinel-A automatic truly never sleeps. A photosensitive sensor on the left side of the body provides dot brightness relative to ambient light conditions. There are no manual controls at all, no Shake N Wake no way for Sentinel-A to be accidentally shut off, ever. Install the CR2032 battery underneath Sentinel-A and youre good to go for two years straight..

GIVE ME LIBERTY The 22mm wide window makes Liberty about the same width as a double-stack 9mm Pistol slide. Liberty is a bit easier to conceal than its bigger brother Justice. Liberty is narrower with flush fitting brightness buttons on the left and a top-loading CR1632. Libertys emitter section is also lower profile, allowing iron sights of .365 or higher to co-witness.. JUSTICE FOR ALL Justice is identical to Liberty except for its larger window, measuring 27mm wide. Justice is great for shotguns, carbines, duty or competition pistols where concealing is not important and even faster sight acquisition is desired. Liberty and Justice share the same RMR footprint, and body dimensions underneath the window. In all respects other than window size, Liberty and Justice are identical, and both are fully compatible with standard ALS law enforcement holsters.. SEEING RED AGAIN Liberty and Justice feature high battery life emitters, available as 3 MOA red dot reticles. Other companies claim impressive battery life figures, but those numbers arent true at the daylight bright settings used for everyday carry. Liberty and Justice get about 4,000 hours battery life at daylight brightness. Coupled with Shake N Wake illumination, we estimate once a year battery changes.. BUILT FOR RETENTION HOLSTERS Compatibility issues can be a major headache when adopting a new piece of equipment, but you dont have to worry. There is no need to go holster hunting or invest in an expensive custom holster setup. Liberty and Justice fit securely in all ALS series duty holsters, both optic and holster fully function as intended.. SHAKE IT, BABY Liberty and Justice feature Shake N Wake motion sensing illumination tech to help save battery life. After four minutes without motion, illumination shuts off. Even the smallest tap or tilt will wake it up to the previous brightness setting. This allows daily carry without wasting battery life..

Dot Size 3 MOA dot 2 MOA dot 65 MOA circle. Parallax Parallax free 100 yards. Waterproof IPX 7 Rated. Auto shut-off 4 hours without movement press Up button to wake. Illumination Positions 10.

GIVE ME LIBERTY The 22mm wide window makes Liberty about the same width as a double-stack 9mm Pistol slide. Liberty is a bit easier to conceal than its bigger brother Justice. Liberty is narrower with flush fitting brightness buttons on the left and a top-loading CR1632. Libertys emitter section is also lower profile, allowing iron sights of .365 or higher to co-witness.. JUSTICE FOR ALL Justice is identical to Liberty except for its larger window, measuring 27mm wide. Liberty and Justice share the same RMR footprint, and body dimensions underneath the window. In all respects other than window size, Liberty and Justice are identical, and both are fully compatible with standard ALS law enforcement holsters.. SEEING RED AGAIN Liberty and Justice feature high battery life emitters, available as 3 MOA red dot reticles. Liberty and Justice get about 4,000 hours battery life at daylight brightness. Coupled with Shake N Wake illumination, we estimate once a year battery changes.. BUILT FOR RETENTION HOLSTERS Compatibility issues can be a major headache when adopting a new piece of equipment, but you dont have to worry. There is no need to go holster hunting or invest in a custom holster setup. Liberty and Justice fit securely in all ALS series duty holsters, both optic and holster fully function as intended.. SHAKE 'N WAKE Liberty and Justice feature Shake N Wake motion sensing illumination tech to help save battery life. After four minutes without motion, illumination shuts off. Even the smallest tap or tilt will wake it up to the previous brightness setting. This allows daily carry without wasting battery life..

Spectra coat HD polymer lens with 10 times the impact resistance over traditional glass lenses. Weapons grade ultra lite polymer housing, optimized for use with polymer pistols, concealed-carry and also slim slide profiles. Stippling pattern on the housing matches p365 and p365xl grip pattern, for an integrated look. 8 vivid, user-configurable daytime illumination levels. Motac motion activated illumination system that powers up when it senses motion and powers down when it does not. Sport type Airsoft.

Prismatic scope with 3X magnification. All the benefits of a red dot plus the built in addition of 3X magnification and great anti-glare, anti-fog, anti-scratch, and hydrophobic glass. Uber long eye relief. This optic is 33 more forgiving of eye placement which facilitates rapid target acquisition. Coupled with Super wide True 10 degree field of view. Trihawk provides 53 ft of view at 100 yards as opposed to less that 36 ft for most of the competition.. Several great reticle choices. All are etched into the glass, so even with loss of battery they still work. 556 308 BDC or 40 MOA Ladder. Red or Green. All come with ten brightness settings. The other six are for those in betweens.. Shake n Wake technology built in. The reticle powers down after 225 seconds of inactivity but instantly powers back on with any movement.. We use our products so Trihawk comes with everything you need, battery, mount, flip up caps, and a honeycomb anti-relfection device.

Do you like rings but greatly prefer the stability of a unified mounting option If so, Hostile Engagement Mount is right for you. This mount provides the option of moving the optic up to 2 beyond the edge of a Picatinny rail This is a superb choice for generous eye relief scopes The Tomahawk and Arrowhead come to mind, although it will work with well with any 30mm tube Low Power Variable Optic LPVO. The entire mount is made from super strong 7075 T6 Aluminum and is finished in a Matte Black hardcoat anodize. To ensure it stays stable and secure T25 torx bolts are used instead of thumb nuts These along with integrated recoil lugs ensure everything stays exactly where you left it One mount with two optics to handle threats near and far with only a tilt of the wrist. As if that wasnt enough, we added a built in RMR footprint, 45 mount for use with an offset back up red dot Kingslayer, Liberty or Justice would all mount up easily with 6x32 bolts.

IN THE BOX Optix wsheath, screwdriver, lens cloth, Battery, and three screw sets.. AUTO BRIGHTNESS MODEL A photosensitive sensor on the left side of the body provides dot brightness relative to ambient light conditions. The brightness adjustment is always on.. COMPACT UNOBSTROCTIVE FIT Shoehorned into this tiny scope is a 16mm x 16mm window, big enough for fast acquisition and sight tracking but small enough that it doesn't affect concealment.. DUTY GRADE Made from 7075 aluminum that is hard coat oxidized, shock proof to 1,500 G forces, and waterproof.. DOUBLE THE LIFE The CR2032 battery effectively doubles the battery life. Whether you choose Sentinel-M or Sentinel-A, expect two years of real-world battery life, even carrying your pistol all day, every day..

The Viper Red Dot Sight has a super low-profile making it perfect for handguns with cut-out slides.. The Viper's low height allows it to co-witness with iron sights and the 6 MOA dot is easy to pick up and get you on target fast. Power and illumination controls are easy for shooters to access and adjust.. The fully multi-coated, ultra-clear lens offers a wide, unobstructed field of view while Armortek coatings protect your lens from oil, dirt, and scratches.. Hard anodized finish- highly durable low-glare matte finish. 1 MOA windage and elevation adjustments move the dot to your point of aim.. Waterproof and shockproof construction ensure your Viper Red Dot is ready for all conditions O-ring seals prevent moisture, dust and debris from penetrating for reliable performance in all environments..