Top 6 Best Swampfox Sentinel

Optic Shim is made to fit between the red dot and the mounting plate.. Fits Shield RMSRMSCRMSWSMS, ADE RD3-018 SPIKE, Sig Sauer Romeo Zero, Leupold Delta Point Pro, JP Enterprises JPoint, Swampfox Sentinel Red dot Sight. All trademarks mentioned belong to their respective owner, this optic shim is made by ADE as a mounting accessory for the mentioned optics. Does NOT fit Trijicon RMRSRO, Doctor, Vortex VenomViper, Burris Fastfire, ADE RD3-006009012013. Depending on the handgun, some handguns need THIS 1degree shim to give extra range of elevation across a wide range of firearms such as the 1911. Should you feel any resistance from the mechanism whilst zeroing the elevation please fit the shim between the sight and the mount with the thickest part at the rear.. What it does While zeroing the red dot sight, some users turned the elevation screw all the way to the end that can no longer turnscrew maxed-out, the location of the illuminated dot is still TOO HIGH, user is UNABLE to adjust the dot LOW enough to zero. Instead of returning the defective red dot, this shim will rise the optic to help user to move the illuminated dot higher to the location to zero. .. Scope base shims Tolerance -.005 Taper 1.0 degree.

Designed to fit Canik Elite TP9 SC, Canik METE SFX, Canik METE SFT, Sig P365XP365XLP365XL SPECTRE COMP, Ruger Max-9, Glock 43X MOS48 MOSnot compatible with regular glock 43x48 that are not MOS, Springfield Hellcat OSP, SW Shield 2.0 Optics Ready, SW MP9 EZ, SW MP shield plus performance center, Walther PPS M2 Optics Ready, Girsan MC1911SC Ultimate or any pistolmounting plateslide with RMSRMSC screw patternfootprint.. Hard coated aircraft aluminum and multi-coated glass. Not plastic body with polymer lens.. ADE SPIKE red dot sight is always powered on with automatic brightness. Operates with a single CR2032 3v battery. With our advanced technology the sight only draws approximate 700 microampere powers to give a very long battery life. The brightness will turn high and low accordingly to the environment brightness.. 4MOA, Weight approximately 17.6 grames0.62oz, Length1.6 x Width.92 x Height.93. Comes with screws for several Optics Ready handguns. Does not comes with any mounting plate such as picatinny mount or plate made for a specific handgun.. Ade SPIKE created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distancegap on some full size optics ready pistols, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight. For non-optics ready pistols that need to use an optic plateadapter to replace the pistol manufacturer equipped rear sight, ADE Spike's rear white dot will act as a pistol factory original rear sight for Co-Witness.. Comes with 3 pairs of screws for Sig P365XLX, Springfield Hellcat OSP and Canik TP9 Elite SC ONLY. The provided screws might NOT work with EVERY compatible pistol listed. ADE makes the red dot to accept the industrial standard footprint. The pistol manufacturer makes the optic cutslide for the same footprint, but they have their own opinions to decide which type screws that the screw holes take.. ADE Does not know the screw spec every pistol manufacture used for their screw hole. Please ask the pistol manufacture what screw specs they used on the hole and ask them to provide the screw. If you cant get the screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size..

This is ADE's new GREEN dot version of RD3-018 Spike. The Spike now available in 3 models. Black body 4MOA Red dot, Black body 4MOA GREEN dotthis one and FDETAN body 4MOA Red dot.. Designed to fit Canik Elite TP9 SC, Canik METE SFX, Canik METE SFT, Sig P365XLP365X, Ruger Max-9, Glock 43X MOS48 MOSnot compatible with regular glock 43x48 that are not MOS, Springfield Hellcat OSP, SW Shield 2.0 Optics Ready, SW MP9 EZ, SW MP shield plus performance center, Walther PPS M2 Optics Ready, Girsan MC1911SC Ultimate or any pistolmounting plateslide with RMSRMSC screw patternfootprint.. Hard coated aircraft aluminum and multi-coated glass. Not plastic body with polymer lens.. ADE SPIKE red dot sight is always powered on with automatic brightness. Operates with a single CR2032 3v battery. With our advanced technology the sight only draws approximate 700 microampere powers to give a very long battery life. The brightness will turn high and low accordingly to the environment brightness.. 4MOA, Weight approximately 17.6 grames0.62oz, Length1.6 x Width.92 x Height.93. Ade SPIKE created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distancegap on some full size optics ready pistols, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight. For non-optics ready pistols that need to use an optic plateadapter to replace the pistol manufacturer equipped rear sight, ADE Spike's rear white dot will act as a pistol factory original rear sight for Co-Witness.. Comes with screws for several Optics Ready handguns. Does not comes with any mounting plate such as picatinny mount or plate made for a specific handgun.. Comes with 3 pairs of screws for Sig P365XLX, Springfield Hellcat OSP and Canik TP9 Elite SC ONLY. The provided screws might NOT work with EVERY compatible pistol listed. ADE makes the red dot to accept the industrial standard footprint. The pistol manufacturer makes the optic cutslide for the same footprint, but they have their own opinions to decide which type screws that the screw holes take.. ADE Does not know the screw spec every pistol manufacture used for their screw hole. Please ask the pistol manufacture what screw specs they used on the hole and ask them to provide the screw. If you cant get the screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size..

Precision CNC Machined from Aircraft Grade Aluminum. This optic picatinny mount made by ADE is to connect to certain type of optic sight to standard 1913 picatinnyweaver rail. It does not connect to handgun because most handguns does NOT has a picatinny rail on top. Designed to use on ADE RD3-018 SPIKE, Shield RMSRMScRMSwSMS and Romeo Zero Red dot sights.. Also Compatible with Leupold Delta Point Pro, JP Enterprises JPoint and Swampfox Sentinel red dot sights. Does NOT compatible with Holosun 407k507k, user MUST grindlots of grinding to completely REMOVEFlat out the two rear pin to fit 407k507k. Ade has is releasing a new plate made specifically for 407k507k in March 2022. Finished in a Matte Black Anodize. Comes with two screws.

Promotes rapid target acquisition while providing a precise point of aim getting shots down range and on target fast. Top load System, no need to Remove the sight to change the Battery. The red dot is compatible with Ade handgun mounts for Glock Barreta HK UPS SW MP SIG P226 Springfield Ruger LC9 LC9s LC380 SR9 SR22 SR40 SR45. Red dot has multi brightness level with one adjustment button. Every time you turn on the dot it stays the same brightness level last time it was turned off. 1.75 length x1.25 width x1.15 height. Shockproof, Fogproof and waterproof for 30 minutes under 4ft water.Feature 1 M.O.A wind age and elevation adjustments with audible click. 6 MOA dot. Come with Protected Cover, Adjustment wrench, Adjustment dailing plate, User Manual and Picatinny mounting plate. Additional mounting plates for hunguns sells separately.

Fully windage and elevation adjustable and lockable Unlimited Eye Relief. Multi Illumination Settings. Powered by a lithium CR2032 batteryIncluded.It is also compatible with varies handgun mounting plates that replace rear sight dovetail.. This Huracan Green Dot Sight fits directly to Optics Ready pistols that does not need to remove rear sight such as Glock MOS, Springfield OSP. It also fits Canik using Canik provided mount marked for DoctorVenom type red dot.. However the front switch of the sight needs to trim down 2mm depends on exact pistol model if the pistol's pre-cut is very short... Comes with an removable picatinny mounting base to attach to any thing with piatinny rail. Fully windage and elevation adjustable and lockable Unlimited Eye Relief. Powered by a lithium CR2032 battery. ADE RD3 006,RD3 009,RD3 012,RD3 013,RD3 015 are designed to fit the slidefootprint of plate made for Vortex Venom,Burris Fastfire,Meopta,Docter,Insight,Eotech MRDS.Any Plate made for those brands also fits this sight..

This green dot sight comes equipped with a Picatinny mounting base and is also compatible with various handgun mounting plates that replace the rear sight dovetail. It's designed to fit the Doctor Footprint PlateSlide seamlessly.. The onoff switch for this sight is conveniently positioned at the front, making it much easier to press compared to red dots with side-mounted switches. It features a 3 MOA dot size and offers 5 illumination settings. The sight is fully adjustable for windage and elevation and can be locked into place. With unlimited eye relief and various illumination settings, it is powered by an included lithium CR2032 battery.. Since its initial release in 2014, we've implemented numerous improvements to enhance its durability, ensuring it can withstand recoil while also improving its ability to hold zero. The front switch, battery housing, and hardware have all been recently updated, reflecting our commitment to continuous enhancement. This product is proudly designed in Oregon.. Although it's feasible to install the optic on a handgun without the assistance of a gunsmith, we highly recommend seeking the expertise of a professional for the installation process. It's essential to note that unprofessional installations, such as improper torque application, can lead to issues like loose screws, an inability to hold zero, damage to the firearm or optic, and even pose a risk of personal injury.. If you're not seeing a perfect round dot but instead observe a splashed dot, half-moon shape, multi-dot, or starburst, there's a high probability 99 that you might have astigmatism without being aware of it. What you perceive is likely a small reflection of the LED light on the lens. A quick and simple way to confirm this is by using your cellphone to take a photo of the dot. If the photo shows a circular dot, you've essentially diagnosed yourself with astigmatism.. ADE RD3-006 Huracan,RD3-009 Crusader,RD3-012 Delta, RD3-012 PRO, RD3-013 Bertrillium ,RD3-015 Zantitium, RD3-028 Ares fit optic cutplate that is compatible with Vortex VenomBurris FastfireDoctor footprint. ADE RD3-018 Spike, RD3-021 Nuwa, RD3-021 NUWA PRO and RD3-030 Apollo fit optic cutoptic plate that is compatible with shield RMSRMSCDeltapoint Pro footprint. ADE RD3-021c NUWAcc fits optic cutoptic plate that is compatible with Trijicon RMRcc footprint. ADE RD3-019 Stingray, RD3-020 Raptor, RD3-022 Artemis, RD3-023 Valkyrie and RD3-029 Trumpet fit optic cutoptic plate that is compatible with Trijicon RMRSROHolosun 407C507C footprint.

ADE is introducing all new APOLLO PRORD3-030PRO. This ADE APOLO PRO is designed to fit any pistolmounting plateslideoptic cut with RMSRMSC screw patternfootprint.. Equipped with Solar Power that allows the red dot sight to continue to be powered when your battery is out. The battery life can last up to 50,000 hours depending on settings.. The APOLLO PRO is always powered on and features an auto-dimming sensor which regulates proper dot brightness based on ever changing ambient light conditions. The brightness will turn high and low accordingly to the environment brightness. Operates with a single CR2032 3v battery. There is no physical onoffbrightness button. The sensor does it all.. Ade APOLLO PRO created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight.. Comes with the adjustment tool, user manual, lens cloth, red dot cover, CR2032 battery, screws. Parallax-free Unlimited Eye Relief. Made of aircraft aluminum in anodized black finish with multi-coated lens. Weight approximately 17.5 grames0.61oz, Length1.6 x Width1 x Height.9. The objective lens is 22mmx16m0.87x0.63. Comes with 3 pairs of screws for Sig P365XLX, Springfield Hellcat OSP and Canik TP9 Elite SC ONLY. The provided screws might NOT work with EVERY compatible pistol listed. ADE makes the red dot to accept the industrial standard footprint. The pistol manufacturer makes the optic cutslide for the same footprint, but they have their own opinions to decide which type screws that the screw holes take..

We have made several improvements since it's initial release in 2016. We have made it more durable to withstand recoil and improved the ability to hold zero. Designed in Oregon.This GREEN dot comes with a picatinny mounting base.. Lenses are precision ground and polished to exacting geometries to virtually eliminate parallax and to provide a very clear, crisp sight picture.This GREEN dot comes with a picatinny mounting base. Other handgun mounting plates are not included.. It is fits directly to Optics Ready pistols that does not need to remove rear sight such as Glock MOS, Springfield OSP. It also fits Canik using Canik provided 1 mount, however the front switch of the sight needs to trim down 2mm.. 3 MOA. Fully windage and elevation adjustable and lockable Unlimited Eye Relief. Multi Illumination Settings. Powered by a lithium CR2032 batteryIncluded.It is also compatible with varies handgun mounting plates that replace rear sight dovetail.. ADE RD3-006,RD3-009,RD3-012,RD3-013,RD3-015 are designed to fit the slidefootprint of plate made for Vortex Venom,Burris Fastfire,Meopta,Docter,Insight,Eotech MRDS.Any Plate made for those brands also fits this sight.RD3-011 only Fits Trijicon ftprt.

Designed to fit Canik Elite TP9 SC, Canik METE SFX, Canik METE SFT, Sig P365XP365XLP365XL SPECTRE COMP, Ruger Max-9, Glock 43X MOS48 MOSnot compatible with regular glock 43x48 that are not MOS, Springfield Hellcat OSP, SW Shield 2.0 Optics Ready, SW MP9 EZ, SW MP shield plus performance center, Walther PPS M2 Optics Ready, Girsan MC1911SC Ultimate or any pistolmounting plateslide with RMSRMSC screw patternfootprint.. Hard coated aircraft aluminum and multi-coated glass. Not plastic body with polymer lens.. ADE SPIKE red dot sight is always powered on with automatic brightness. Operates with a single CR2032 3v battery. With our advanced technology the sight only draws approximate 700 microampere powers to give a very long battery life. The brightness will turn high and low accordingly to the environment brightness.. 4MOA, Weight approximately 17.6 grames0.62oz, Length1.6 x Width.92 x Height.93. Comes with screws for several Optics Ready handguns. Does not comes with any mounting plate such as picatinny mount or plate made for a specific handgun.. Ade SPIKE created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distancegap on some full size optics ready pistols, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight. For non-optics ready pistols that need to use an optic plateadapter to replace the pistol manufacturer equipped rear sight, ADE Spike's rear white dot will act as a pistol factory original rear sight for Co-Witness.. Comes with 3 pairs of screws for Sig P365XLX, Springfield Hellcat OSP and Canik TP9 Elite SC ONLY. The provided screws might NOT work with EVERY compatible pistol listed. ADE makes the red dot to accept the industrial standard footprint. The pistol manufacturer makes the optic cutslide for the same footprint, but they have their own opinions to decide which type screws that the screw holes take.. ADE Does not know the screw spec every pistol manufacture used for their screw hole. Please ask the pistol manufacture what screw specs they used on the hole and ask them to provide the screw. If you cant get the screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size..

Designed to fit Canik Elite TP9 SC, Canik METE SFT, Sig P365XLP365X, Ruger Max-9, Glock 43X MOS48 MOSnot compatible with regular glock 43x48 that are not MOS, Springfield Hellcat OSP, SW Shield 2.0 Optics Ready, SW MP9 EZ, SW MP shield plus performance center, Walther PPS M2 Optics Ready, Girsan MC1911SC Ultimate or any pistolmounting plateslide with RMSRMSC screw patternfootprint.. Hard coated aircraft aluminum and multi-coated glass. Not plastic body with polymer lens.. ADE SPIKE red dot sight is always powered on with automatic brightness. Operates with a single CR2032 3v battery. With our advanced technology the sight only draws approximate 700 microampere powers to give a very long battery life. The brightness will turn high and low accordingly to the environment brightness.. 4MOA, Weight approximately 17.6 grames0.62oz, Length1.6 x Width.92 x Height.93. Comes with screws for several Optics Ready handguns. Does not comes with any mounting plate such as picatinny mount or plate made for a specific handgun.. Ade SPIKE created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distancegap on some full size optics ready pistols, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight. For non-optics ready pistols that need to use an optic plateadapter to replace the pistol manufacturer equipped rear sight, ADE Spike's rear white dot will act as a pistol factory original rear sight for Co-Witness..

DUTY GRADE DARN RIGHT Other companies are producing slimline pistol dots with plastic bodies and clear polymer lenses. Thats not our style. Sentinel is crafted from CNC machined 7075-T6 aluminum, hard coated in matte black, and features multicoated glass of the same excellent quality used in our long-range precision rifle scopes.. BUT WHAT DOES IT FIT Sentinel is really small. About an inch tall, an inch wide, and 1.6 inches long. Shoehorned into this tiny scope is a 16mm x 16mm window, big enough for fast acquisition and sight tracking, small enough that it doesnt affect concealment at all. Sentinel will any slimline slide with an RMSc footprint incorporated.. BET YOUR SS DEPENDABLE A concealed carry optic must be ultra dependable, because you are literally betting your life that it will be ready when called upon. Sentinel is dunk it waterproof when installed using the included flexible seal that fits between the optic and footprint. It is shock rated to an incredible 1500 G.. MANUAL VS. AUTOMATIC, THE CHOICE IS YOURS Sentinel-M manual features ten manually adjusted brightness settings accessed via digital push buttons. Shake N Wake motion sensing preserves battery life when Sentinel-M has been still for about 4 minutes. With new motion, Sentinel-M resumes its previous brightness level.. Sentinel-A automatic truly never sleeps. A photosensitive sensor on the left side of the body provides dot brightness relative to ambient light conditions. There are no manual controls at all, no Shake N Wake no way for Sentinel-A to be accidentally shut off, ever. Install the CR2032 battery underneath Sentinel-A and youre good to go for two years straight..

Choose from 3 MOA dot, red circle dot, or green circle dot reticles. RMR footprint scope base for maximum compatibility with pistol slides and included low picatinny mount. Uses CR1632 battery, Change via side tray with no optic re-zero needed with Auto shut off after 4 hours with no movement UP button to wake. 13 illumination settings to match your needs. Weighs only 1 oz in pistol configuration, 1.3 oz with rifle or gun mount. Dimensions 1.8L 1 W and 1.4 H using the long gun mount.

GIVE ME LIBERTY The 22mm wide window makes Liberty about the same width as a double-stack 9mm Pistol slide. Liberty is a bit easier to conceal than its bigger brother Justice. Liberty is narrower with flush fitting brightness buttons on the left and a top-loading CR1632. Libertys emitter section is also lower profile, allowing iron sights of .365 or higher to co-witness.. JUSTICE FOR ALL Justice is identical to Liberty except for its larger window, measuring 27mm wide. Justice is great for shotguns, carbines, duty or competition pistols where concealing is not important and even faster sight acquisition is desired. Liberty and Justice share the same RMR footprint, and body dimensions underneath the window. In all respects other than window size, Liberty and Justice are identical, and both are fully compatible with standard ALS law enforcement holsters.. SEEING RED AGAIN Liberty and Justice feature high battery life emitters, available as 3 MOA red dot reticles. Other companies claim impressive battery life figures, but those numbers arent true at the daylight bright settings used for everyday carry. Liberty and Justice get about 4,000 hours battery life at daylight brightness. Coupled with Shake N Wake illumination, we estimate once a year battery changes.. BUILT FOR RETENTION HOLSTERS Compatibility issues can be a major headache when adopting a new piece of equipment, but you dont have to worry. There is no need to go holster hunting or invest in an expensive custom holster setup. Liberty and Justice fit securely in all ALS series duty holsters, both optic and holster fully function as intended.. SHAKE IT, BABY Liberty and Justice feature Shake N Wake motion sensing illumination tech to help save battery life. After four minutes without motion, illumination shuts off. Even the smallest tap or tilt will wake it up to the previous brightness setting. This allows daily carry without wasting battery life..

EQUIPMENT INCLUDES HE407K-GR X2 Green Dot Reflex Sight, Coin Battery CR1632, multi-tool, user manual, and lens cloth. The HE407K-GR X2 is an open reflex optical sight designed for adult concealed carry equipment applications.. LONG BATTERY LIFE Features include Super LED high capacity lithium battery to power the optic with up to 50,000 hours of battery life. With the long battery life span, it makes this the perfect sight to carry on long hunting treks.. ADVANCED TECHNOLOGY The X2 Series optics has two improvements. Lock Mode from our 2018-2019 LE when activated, locks the buttons preventing inadvertent setting changes and the buttons have been redesigned to place them lower and out of the way.. ADVANCED TECHNOLOGY The X2 Series optics has two improvements. Lock Mode from our 2018-2019 LE when activated, locks the buttons preventing inadvertent setting changes and the buttons have been redesigned to place them lower and out of the way.. ADDITIONAL FEATURES Optic sight features include 12 brightness setting 10 DL 2 NV compatible, convenient side-mounted battery compartment, parallax-free and unlimited eye relief..

Country of origin China. LONG BATTERY LIFE Features include Holosuns Super LED with up to 50k hours battery life. Its long life span, makes this the perfect optic sight to carry on long treks.. ADVANCED TECHNOLOGY There are 12 different brightness settings, including dim settings compatible with night-vision devices for nighttime use. Parallax free optical design, with unlimited eye relief. SHAKE AWAKE Holosuns Shake Awake Technology shuts the LED off during periods of motionlessness. The amount of time it takes for the LED to deactivate enter Sleep Mode is user programmable..

All impact forces hit the black stainless steel Ironsides Shield instead of the optic. One handed barricade racking, covered. Dropping in a 3Gun match, covered. Abuse of daily carry and other impacts are all routed around your optic and straight to the mounting footprint area. Our dot sights have a great guarantee. That doesnt mean you cant break them. By putting an Ironsides Shield over the optic, you insure it is ready when you need it. Includes one set of longerscrews 6-32 x .393 T10. These provide a deeper anchor base for greater shock protection. The Ironsides Shield is made from blackened 304 stainless steel. This reduces visibility and glare as well as being as close to rust proof as steel gets. Insurance for those who know their optic.

Prismatic scope with 3X magnification. All the benefits of a red dot plus the built in addition of 3X magnification and great anti-glare, anti-fog, anti-scratch, and hydrophobic glass. Uber long eye relief. This optic is 33 more forgiving of eye placement which facilitates rapid target acquisition. Coupled with Super wide True 10 degree field of view. Trihawk provides 53 ft of view at 100 yards as opposed to less that 36 ft for most of the competition.. Several great reticle choices. All are etched into the glass, so even with loss of battery they still work. 556 308 BDC or 40 MOA Ladder. Red or Green. All come with ten brightness settings. The other six are for those in betweens.. Shake n Wake technology built in. The reticle powers down after 225 seconds of inactivity but instantly powers back on with any movement.. We use our products so Trihawk comes with everything you need, battery, mount, flip up caps, and a honeycomb anti-relfection device.

First focal plane FFP Sharpshooter etched reticle stays true at all magnifications. MOA and MIL MRAD reticles paired with 0.25 MOA 0.1 MRAD clicks Outstanding eye box for ease of us. Outstanding eye box for ease of use even at high magnifications. 11 red reticle illumination settings. PushPull locking, Zero-resettable turrets.

Extremely low power consumption. Windage and elevation click adjustments. 10 reticle brightness levels. 100 waterproof and dustproof and Steel protective shield. Ambidextrous digital switch brightness controls.